Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I've searched the forum to see if anyone else has had the same issue as I'm having but couldn't find anything. I'm trying to do DFU via USB with the nRF52840 on a custom...
Dear Nordic,
We have almost completed development with nRF52810.
We are trying to improve the accuracy of product operation.
RC oscillator(LFRC) is currently used...
I used the Adafruit Bluefruit NRF52840 LE and added some simple code to this existing timer/counter for pulses: https://devzone.nordicsemi.com/f/nordic-q-a/62633/nrf52-timer...
Hi,
While going through some of the peripheral examples in 'nRF5_SDK_17.0.2', I found it puzzling to see that
the legacy (nrf_drv_*) and nrfx_* drivers are simultaneously...
Hi all,
trying to get CAN-bus support under Zephyr. Have a seed CAN bus shield link connected to PCA10040. The shield use SPI2 connected to MCP2515 CAN controller link ...
Hello
Is it possible to use the qspi of the nrf5340 for custom spi devices? I need the quad spi for the 96MHz speed which the normal spi does not have.
I know of the nrfx...
Hi there,
I am using the Nordic SDK 16.0.0 on an nRF52840 with FreeRTOS. I am quite familiar with using FreeRTOS, but hadn't needed to delete a task until recently. It seems...
Hi everyone,
How could I disable notifications from a characteristic when the peer is get disconnected from the the peripheral? My problem is that when notification are...
Hi,
I was investigating the registers of the nrf9160 using segger embedded studio and found POFCON, which is not mentioned in the documentation.
Can you provide...
I need to add some IPSO objects for our project. It is not quite obvious to me if I need to create modules similar to i e ipso_temp_sensor.c or if it would be enough to use...
Hello, guys!
We are desiging our custom board based on nRF9160 SiP. The board will be battery powered. Li-Ion rechargeable batteries will be used to supply the device. ...
Hi to all,
i am developing a device based NRF52840 soc, and i want to implement a device that need to store some public/private key in somewhere. i know that cryptocell...
Hello,
I am developing on the NCS 1.4.0 and on a NRF9160DK. I am working on the asset_tracker example and I noticed that the code sends an assisted gps request to NRF...
