Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I am developing a robot controller(Central, nRF51822).
However, I am having a problem with UUID.
And I am using the ble_central (s130 ble_app_uart) example.
The figure...
Hi
I am developing a bootloader for nRF52840 using SDK 15.2.0 and s140_nrf52_6.1.0_softdevice, that should support both USBD and BLE transports.
The first transport layer...
We are using NRF52840 with Softdevice 340 and several sensors connected via ANT and BLE. NRF is connected to STM32 via serial UART connection and use ANT serial protocol for...
I am using PPK to measure current. The system uses 2 CR2430 in parallel.
I observe that
1. When using the battery as external supply, the battery voltage drop to 2.5V...
I am using the original board. It does not have a 32kHz crystal.
So I want to use the built-in RC oscillator.
In addition, use the time example of nRF5_SDK_16.0.0. "NRFX_CLOCK_CONFIG_LF_SRC...
Hello,
I am using nRF52840 S140 v7.0.1. I have few queries on DTM functionality.
1) As per standards, we can do DTM test either by sending HCI commands or UART commands...
Hi,
Using Eddystone example I configured EID and TLM slots. I see in nRF connect app both EID and encrypted TLM(encrypted data, salt, MIC).
How to exactly decode the...
Hello,
we are experimenting with the Nrf52811 CTE feature and have a few doubts concerning the documentation. We program our experiments with bare-metal (no soft device...
Hi,
I am working on one business use case. The basic requirement is to monitor the outdoor air environment from different locations. I want to try out the initial things...
Hi,
For nRF52840 BLE, in the DFU (OTA) example (buttonless OTA):
../nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_buttonless_dfu
How scanning is done? Or where...
Hello, I'm using Zigbee SDK 4.0.0 with Segger Embedded Studio 4.30 and custom pca10059-compatible debug board.
I ran into difficulties when trying to subscribe to attributes...
Hi,
I am using custom gatt service & I have included some of the code which supports swift pairing from ble_hid_mouse example. Here is my sniffer log -
& the jlink rtt...
