Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, I need to support both BLE update and serial update with sdk 17. Going through some past post, the idea is clear.
1) Start with DFU_BLE example project.
2) Add the...
From my understanding, notifications have guaranteed in-order delivery at the lower levels. I'm working on a small file transfer system out of an nrf52840, trying to decide...
Dear Sir/Madam,
As a BLE solution in our products one of the candidate ICs is NRF52820. Our current PCB is a 2 layer one. But the reference design for NRF52820 is 4 -layer...
I'm evaluating if it is possible to build my Bluetooth application using the nRF Connect SDK (v1.3.0) instead of the nRF5 SDK and not be worried about any certification issues...
The nRF Connect app on iOS is able to display "Appearance" information that displays known devices such as a Wearable or TV set. After some research, the Appearance value...
Hi,
What is the BLE Bluetooth ID for the nRF52810 / S112 configuration?
Is there a list of all Qualified Pre-tested Component ID somewhere?
Thanks for your help
M...
Hi,
I am requested a SUPL-C license for running agps. But I got reply mail as SUPL-C license application was not approved.
I have an active/approved DevZone account. ...
Hi,
I am trying to put the micro nRF52 in sleep in the configuration "System OFF, No RAM retention, Wake on GPIO " in order to spend 1.2 uA.
After start:
configure...
I used SDK v15.2.0 (for older project) and SDK v17.0.0 (newer ones), for 52832 and 52840 (and perhaps in other platforms) I noticed there is discrepancy in UART baudrate config...
Hi,
Are there any examples utilizing the nRF9160 RTC? I want to timestamp my data that I send to the cloud because my use-case involves queuing up data for extended periods...
It seems that the socket errors in https://devzone.nordicsemi.com/f/nordic-q-a/64930/https_client-sample are caused by at_cmd_write being called before at_comms_init :
Breakpoint...
Hello,
Our product is running on a nRF52832 with SDK 15.2.0 and softdevice 6.1.0 and I am wondering if there is a way of verifying that all BLE related functionality's...
I can not connect to nRF52840 DK with running Bluetooth: Peripheral HIDS keyboard example from macOS. And also with some other examples which I tried, but I chose this one...
Hi and thanks in advance for help!
I have purchased an nRF52832 DK and the nRF52832. I'm a newbie to embedded systems, and nordic products. I just started to understand...
Hi there. I am working on an application where i need to transfer audio signal from a microphone connected to the nRF52840 to a smartphone. Are there any working examples...
