Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hey,
I´m working on a project based on nRF52840, SDK 15.0.0 Softdevice s140 v6.0.0 running FreeRTOS.
I´m reading data from an external Flash via SPI and transmitt the...
Hi
I am running UBUNTU 32bit
Which "nRF Connect for Desktop" version does run on 32bit LINUX?
I have tried several with no success.
Thanks for any help ti get...
hello.
I want test dfu example.
so I was compile & download secure_bootloader example(nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader).
I just compiled and...
Hello everyone,
I want to know about Connection parameters updated means and why to use it as mentioned above and when did the next connection parameter is updated and...
In a current project we have a nRF52 Bluetooth application where the Central communicates directly with a Peripheral (also nRF52). The nRF5 SKD V14.0.0 or newer is used for...
Hello,
I have been following this case to create my own bootloader for nRF52810, but I'm using gcc/Segger Embedded Studio instead of Keil.
I have modified bootloader_secure_ble...
Hi.all:
I'm doing a project, it include freeRTOS+emwin(TFT screen SPI-->32Mhz)+BLE(central+peripheral)+FATFS+flash(qspi)+TF card(spi)+GPS(uart)+wifi(uart)+other IC(spi)...
I am working with a SmartThings Multipurpose Sensor connected to a nRF52840-DK running the ZigBee CLI as a coordinator. I am able to have the sensor join the network and I...
SDK11, NRF51822
if I use the fstorage_test at the applicaiton_init(void), then runs ok.
but on my product, I use a key to power the system, if I use the fstorage_test...
We are implementing DFU over serial to the nRF52832 from another microcontroller.
We are using SDKv15.30 and a slightly modified the serial bootloader from the DFU bootloader...
Hello, I am developing a big project with the nrf52832 + several peripheral devices and I want to integrate the notion of unit test to my project (in Segger embedded studio...
When trying to build my BLE Mesh app based on light_switch server example app from nrf5 SDK for Mesh with added functionalities (like detecting GPIO state changes and firing...
I'm attempting to create a DFU update using the the ble_app_uart example coupled with the BLE DFU bootloader. It's not unlike this case .
SDK = v16.0.0
nrfutil = v6.0...
Hello Nordic Team,
I have loaded the ble_app_uart example on my custom hardware. There is a button connected to P0.13. When that button is pressed I receive a NRF_BREAKPOINT_COND...
