Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Versions:
Windows 10 Enterprise: Version 1803
SEGGER Embedded Studio for ARM (Nordic Edition) V4.20a (64-bit)
Python: 3.7.4
pip: 19.2.3
west: v0.6.2
nrf repo:...
The nRF5SDK has a rich set of examples illustrating extensive use of the BLE APIs, including full examples of the Blood Pressure profile and other health device profiles....
Hi,
I am using nrf51422 dk board using sdk 12.3 and soft device s130 in keil5 ide. In our project i am using nrf51422 board as central and other controller Bluetooth board...
Hello,
I'd like to evaluate the Rust HAL for the nrf52 family of devices. But before that I was asked to inquire about the stage of development of the HAL and the support...
I am experiencing an issue with the nRF52840 dongle and programming UART pins. First off, I have developed my application on the nRF52 DK and it works fine and now I am programming...
Hi , I need use the DFU ble without have to generate a packet with the nRFutil. I wan't put a open bootloader on the board, don't need to be secure just easy and fast. But...
I am trying to find the hardware datasheet for the speaker on the Nordic Thingy 52 - can someone help point me towards it?
My end goal is to learn about the characteristics...
Hello!
I have been trying to implement the serialization for STM32L476. During my development I discovered that the deserialization of the SD_BLE_GAP_ADV_SET_CONFIGURE response...
We have a custom board with nrf51822 chipset, and we need to implement the firmware update process, which can support both over-the-air and uart type firmware update.
1...
Hi, we are contemplating moving an existing application to a nordic chip, the nRF52832.
https://infocenter.nordicsemi.com/pdf/nRF52832_PS_v1.4.pdf
Our previous CPU uses...
I'm in the process of implementing a custom layer above ESB in order to allow more than 8 devices to communicate with a receiver (By tagging packets with a device ID)
I...
I used nRF52 SDK V15 and tried to load the sample BLE HID apps into the nRF52-DK Development Board.
I tested both ble_app_hids_keyboard and ble_app_hids_mouse. Both apps...
We have exiting BLE 4.0 device, which should be updated to the mesh. nRF52832
In the DFU for BLE4.0 you could update the booltoader and the softdevice with one update, with...