Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi,
I'm using nrf_serial to configure and then read data from a GPS engine, but I am getting unrecoverable OVERRUN errors on start-up if the GPS device is sending data when...
Hello
the setup is a nrf52840, the sdk15.3, Softdevice s140, apps: open bootloader and blinky app
Is there a way that the DFU mode is always there, at the moment its only...
Hi,
We are in the HW verification stage of a product with an nRF52 series MCU. We were easily able to measure the 32MHz XTAL accuracy using the buffered output feature;...
Hello, Dear Support!
From the DevZone I downloaded ntf5-multilink-example-master. Here . Thanks for developers. The solution in SES was built and uploaded without any troubles...
I am using 'Segger Embedded Studio'. While changing the settings of a project in options, why we select Private Configurations (common)? I have seen this procedure in many...
Hi,I had a new project base on nRF52810. I watnted to created a timer, but the note mentioned " increase the value of the macro APP_TIMER_MAX_TIMERS by one ".I couldn't find...
Hi,
is nRF9160 SiP comes with eSIM? or do I need to insert external SIM in socket which is traditional method?
Do I need to external chip antenna? does that antenna...
Hi:
Because our project using much nRF pin resources, we have to use the defualt function NFC pins (P0.09 and P0.10).we want to set these two pins as uart function ,but...
Hi everyone,
I m nRF52 beginner and trying to understand that functions.
I have the few of qustions about DFU.
1. Is it that the mean of DFU equels "OTA DFU" referred...
I'm looking for a way to reliably determine (from the applications viewpoint) if a notification was successfully transmitted. Currently, we're having some issues when the...
Hello,
I am new to nrF52 480 chip. I am working on SDK15.3.0_59ac345's beacon code but have no result in the attempt to add device name to the existing beacon example. ...
Hey guys. I was working on a PCA10059 dongle. Now, I need to select suitable NRF52840 module. I know that there are some changes required in the code when I use module like...
Good morning,
In order to save some user data in flash, I want to fix page size to 32 bytes. It will be more useful for me, and it will be easier according to my project...
I've been playing around with the UART drivers on SDK 15.2. No issues with the Legacy (w/DMA) however I've tried switching over the NRFX_UARTE driver and I can't get the driver...
Hi,
Our device is based on nRF52840 SDK 15.0.0
The device verifies signature of incoming messages (which were sent over BLE from PC application) using ECDSA with spec256r1...
