Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
i use a 52832 module scan BLE advertisement signal, and found it can recived lowest DB value is -92db. but i use my Phone to scan same advertisement signal, it can recived...
Hi
I am using the nrf52832 DK for my project.
Using ble i need to establish wireless connection b/w the android phone and the board.
I need to send data from the phone...
During manufacturing verification we want to run some tests that will require us to talk to our custom nRF52840 device over bluetooth.
The ideal solution for us would be...
Hi
In the infocenter, I can find the important note which says, that to run nRF5 SDK for Mesh v2.2.0 on an nRF52832, nRF5 SDK 15.0.0 as well as the softdevice S132 v5...
The scratchpad is overflowing when generating a keystream prior to a CCM decrypt operation.
The size of the scratchpad is calculated according to the formula in the product...
is there any tutorial that shows me how to read data from the BLE using android. My NRF 52840 is connect to my device(Which is i expected data to read from) i am able to send...
To the kind attention of Nordic,
while I'm planning to do a software porting from nRF24 to nRF52840, I've been studying some of the usb applications you provide in your...
Hi,
I am a newbie with zigbee on nRF52840.
I have tried serveral days with zigbee SDK but have troubles to work.
Finally i have found that example zigbee/light_control...
Hello!
We have nRF52832 chip on our product and we have some problem with one of its IOs.. We configured P0.16 as RX of UART, And when we run it we see this behavior of...
my example project: wireless_uart_raw_first_pca10056
chip : nrf52840.
i want to make my application timer in the my example project. time tick is 100 msec. in every 100...
Is it possible to get the Build Type from the Factory information configuration registers (FICR)?
From https://infocenter.nordicsemi.com/topic/comp_matrix_nrf52832/COMP...
Hi
I have some question about OTA .
1.The nRF SDK hvae twos way for OTA: single bank and dual bank;The nRF Mesh 3.10 too?Because my firmware maybe very large,so I want...
Dear all,
I am having issues with service discovery of two primary services ( Battery and one propriotary based on NUS) I am currently using SDK 14.2 on NRF52832 chip running...
Hi, I'm trying to use the Seggar Embedded Studio to debug my code, but the Seggar Embedded Studio can only recognize the nRF52840 development board, not the external device...
Hi,
On my previous question https://devzone.nordicsemi.com/f/nordic-q-a/47762/certification-when-bt-off ,
I got the answer about certification.
And now, I want to...
