Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi, I've encountered a problem described here: https://devzone.nordicsemi.com/f/nordic-q-a/37917/nfc-issue-when-migrating-to-sdk11 Since I could not figure out the issue,...
SDK 15.0, PCA 10056 (1.0.0)
Is it possible to let the relay-example from the SDK 15.0 run in a way, so that the long-range feature of Bt 5 is supported between the Peripheral...
Hello,
I'm using a nRF51422 uController (Custom board) with the Softdevice s130 withe SDK 11. I want to go back into the bootloader from my application after I told the...
Hello Everyone ,
By using sdk version 15 for NRF52840 I wish to connect the lsm9ds1 sensor to it and using seggar embedded studios IDE. The header files available in google...
Hello, what is the best way to provide optional enable or disable option for a user in terms of keeping BLE module powered on or off. I am thinking of 2 options , can you...
Hi everyone,
I'm currently working on a nrf52832 board and i got an issue on Gpio config after a reset.
I configure a gpio with a register value of 4, low level, output...
Hello. I am reading this manual infocenter.nordicsemi.com/index.jsp and trying to compile but there is an error durring linkage phase, Linkage nrf_init: undefined symbol ble_conn_params_init...
Hello Nordic team,
I already managed to get into DFU bootloader using buttonless DFU service, and successfully triggered application uploading process, but the system randomly...
Hello, To use the nRFMesh app which Project needs to be flashed to the Nrf Board ( I have nrf5832) . I see there are following workspaces : (1) nrf5_SDK_for_Mesh_v2.1.1_src...
Hi,
Board PCA10056. PC: Windows 10 BLE 5.0 - Intel AC9250. Any examples from nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral
When I trying to connect from desktop to PCA10056...
What happens: if I send a serialization packet whose last byte is SLIP_END (0xC0) or SLIP_ESC (0xDB), the program crashes in an assert in ser_hal_transport.c:141.
Why: The...
Dear nordic,
I need a help to working nrf52840 dongle. It's not working when i press reset button led not flashing.
i don't know what happen to dongle can you help me...
Hi All, I am working on a problem for last 2 days and cannot find a solution, I tried everything and read many posts from others however nothing worked so far, either it seems...
So, another 2 hours down tonight converting to NRFX, this time it is trying to get the SPI to work.
This line -> static const nrfx_spi_t m_spi_master_0 = NRFX_SPI_INSTANCE...
Hi,
I'm trying to use twi and spi in the same project. But it results in this error:
.\_build\nrf52832_xxaa.axf: Error: L6200E: Symbol SPIM0_SPIS0_TWIM0_TWIS0_SPI0_TWI0_IRQHandler...
