Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi Everyone
I am able to configure BLE on the template project and it is sending data from nrf52840 to BLE nrfconnect app using the function nrf_ble_data_send() .
However...
HI All,
I am trying to upgrade sdk v11 to sdk v13 in my project and after compilation i am facing Linker Error as mentioned below.
binaries/app/SmartTag2/dfuFlash.c.o...
Hi :
I have the same problem. I try to flash program to the Dongle using MCP. Every time I program the Dongle, the MCP log report: "NO response from master emulator". What...
Hi all,
I am using SDK version 15, SES IDE.
I am working on Dust sensor, for that i am using SAAADC example code, I want to read the ADC value from the pin, like this...
Hi Sir,
Based on the nRF5-SDK-for-Mesh , it mentions " release with a Bluetooth mesh profile v1.0 qualified stack".
Do we already have the QDID information for Mesh profile...
Hello,
Can i implement same functionality provided by NXP Mifare DESFire EV1 to nRF52832?
If yes, where i get the details and reference code for the same.
I want...
Hi Sir
I tested the cli example or uart example of SDK15, the uart response data are wrong and slowly.
I have no idea what happened. please help.
------------------...
I am currently using mesh sdk 2.0.1 and I plan to migrate to 2.1.1. I saw this while comparing the light_switch example of the two sdks.
proxy server is not supported...
I am using nrf52832, and used mpu 9250. I want to store the data of mpu 9250 in external and internal flash memory. will you help me how to do this?
the odr of sensor is...
Hi,
I am developing an application using the nRF52840 as NCP with a raspberry pi as the primary processor, using wpantund. I have 3 devices (3 raspberry, each with its own...
In most of the examples the FIRST_CONN_PARAMS_UPDATE_DELAY define is set to something like 5000ms. Is there a reason it needs to be that long? I would like to switch to a...
Hi,
My question is quite easy. I need to use 36 or 38 (maybe something else frequency as well) kHz clock in our device. How it is possible or is this possible at all ? I...
Hello All
Since 3 days now, I am trying to program my third party beacon board PTR9048 with the PCA10028. I'm pretty sure, that I connected it correctly, because I can...
