Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using PCA 10040 development boards with soft device version s132_nrf52_3.0.0 to investigate Central/Peripheral communications.
A PCA 10040 acts as a Central making...
Here is calibration of UART data using ADXL345.
and the data is followed by x, y & z value, for example x = -42, y = 20, z = 268. and then after calibrated 10x which is...
We are upgrading an existing product to use Bluetooth instead of the parallel port.
It must support >20kbit/sec communications between the device and the host PC.
We...
Hey Nordic devzone,
I am tinkering with the following multiprotocol examples:
ble_thread_dyn_mtd_coap_cli (client)
ble_thread_dyn_template (server)
Currently the client...
Hi, I'm using nRF52832 with sdk 13.1.0(softdevice 4.0.2). I had trouble to connect nRF52832 in some android smart device.When I restart Bluetooth,Sometimes there are problems...
Hi, I'm using nRF52832 with sdk 13.1.0(softdevice 4.0.2). I had trouble to scan nRF52832 in android smart device.When i disconnect the device a long time when the status is...
hello,
I use my own code to test IOS message notifications ,
call nrf_ble_ancs_c_request_attrs function， then did not receive the data source,
Triggered the BLE_ANCS_C_EVT_NP_ERROR...
I am following blogs and questions for image transfer with nrf52 and arducam on this site and github . I can see we can use arducam OV2640 module. It has FPGA chip at back...
Hi all , I have a trouble . I am using ble_app_hrs_rscs_relay example . I modify it for NUS service . I have 3 board . peripheral <-> role <-> central via NUS . It work fine...
Im following the example Alert Notification Application and read this instruction:
In nRF Connect, create the Alert Notification Service (ANS) server by performing the...
Based on my experiment, ATT_MTU sample application can achieve throughput of 900 Kbps with the following settings:
SDK 14.2.0
ATT MTU size: 247
Connection interval...
I have a Nordic nRF52-DK that I am using to create and run programs written using the mbed compiler. I have followed the instructions outlined here on the mbed website( os...
Hi
I using nrf52832 to implement a high throughput transmit sensor raw data.
I found post here talk about send multiple-packages once.
I also found this , but I couldn...
Hello,
I try to read temperature with embedded sensor. Works well with example but crash when using SoftDevice 3.0.0 on nRF52328. Was working with SoftDevice 2.0.0.7.alpha...
