Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm using the nRF21540 DK with the Power Profiler Kit II in ampere mode for measuring current draw. I had the gain set to +20 dBm for testing but I noticed the system was...
Hi,
We have five NRF5340DKs with us and off late it seems three of them does not get detected by the PC. In fact, what i understand is that the interface MCU seems to be...
Thingy:91X rev 1.0.0
NCS 2.6.2 own custom application
Quiescent current measured with PPK II and extension board:
nRF53x 2µA, OK
nRF70x 0µA, OK
nRF91x 17µA, OK ...
Hello,
We are in the feasibility phase of updating a product to include a nRF9151 modem connected to a nRF52840 via a single UART. The modem will operate in SLM (Serial...
Hi,
Today the nRF Connect extension isn't working anymore: it doesn't show or let me select an SDK or toolchain.
I have tried on 2 separate computers where it was still...
I am using the latest (I believe) nRF Connect for VS Code extension, version 2024.12.55. But when I "Create a new application" and pick the ncs-example-application, it only...
Our nRF5340 application requires a lot of serial ports, but 2 of them are only used for a second during configuration and are otherwise (99.9% of the time) idle. If we could...
I am a complete newby to Nordic parts and the VB design environment so please bear with my ignorance. I have just purchased a nrf52840 development kit and have successfully...
Hello,
in an earlier entry I was asking about getting multiple BIS streams, where you led me to the nRF Auraconfig Sample.
I am now using this sample and got it to run...
I'm in the process of migrating my project from NCS 2.6.1 to 2.8.0.
My project consists of a BLE application with MCUBoot as the only boot loader.
I've already updated...
hello,
I Have two nRF52833 that I have communicating over BLE. I am using soft device S140. I have my data packets use the default data length maximum of 20 bytes. I am...
I found a link
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/matter/overview/integration.html
which says MATTER protocol support is available with nrf...
nRF5280, nRFSDK 17.0.1, SoftDevice 7.2.0
The nRF52840 data sheet describes the RADIO->FREQUENCY register this way:
And describes the legal values for it in this...
Hello,
I have an application running with a BLE peripheral and our proprietary TSCH wireless stack using an integrated radio. The hardware sharing is done through the MPSL...
It seems like most or all of the sample code contains README.rst files as their documentation. What is the preferred/suggested way to view these in rendered (i.e. not raw...
