Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have some nRF52840 USB Dongles that I would like to turn into a generic BT receiver for SBC's that does not already have BT/WiFi chipset onboard. I was hoping I could program...
My laptop does not detect my dongle after I program it through nrfConnect. I am thinking that maybe I have to reflash the pca 10059 firmware, but I do not have any nrf development...
Using nRF5340 hci code, I've been able to get a device that connects and authenticates with two central devices. However, after connecting with one central device, I no longer...
Dear Forum,
Knowing that nRF9161 SoC contains two microcontrollers: modem microcontroller (MCU) and application microcontroller (MCU):
1. Is it possible to check what...
I am developing a touch keyboard. (using SDK 17.1.0, nRF52840) Of course, this product connects to all OSes such as Windows/iPad/MacBook via BLE. However, there are keys that...
Hi there
For proper playback of LE Audio, it's required to get the current time of the Bluetooth Controller.
In the LE Audio examples (nrf/application/nrf5340_audio) on...
Hi,
I'm trying to get the PWM to work to operate a vibrator connected to the nRF54L15 PDK. I'm basing my activity on lesson4 - pwm as I'm also new to Zephyr (but experienced...
Hi Community,
I made a custom board based on thingy53.
the custom board can be flashed with nRF5340-DK, I see the " merged_domains.hex " is flashed.
Also tried with...
Hi
Default value of NRF_SPIM0->IFTIMING.RXDELAY = 02 based on the datasheet, but it always shows 0x00 on debugger and I can not rewrite it.
Has anyone entered the same...
I want to use the example of "Wi Fi: Shell" to set TWT parameters by referring to the official documentation：
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols...
I see that the NRF24L01P is not recommended for new designs.
Since this product is in our production currently, we want to now the following things
When will the NRF24L01P...
Hi,
I'm trying to build the ZigBee light bulb sample on nRF52840 dongle.
It compiles. 1 LED blinks, and the other 2 are steady, which supposedly indicates that the dongle...
We are using an nrf52833 with the nrf21540 FEM and are getting a fault. Even with a basic BLE example, we are getting this fault. When we use a board that does not utiliize...
I need to detect the VCC voltage on the nrf52833 on power-up and wait till it slowly ramps up to 3V. Is there a way to do this using the Power-Fail Comparator. I found another...
I am using an nrf52833 with both 32.768 kHz and 32MHz external crystals (identical to the DK). When I go down to -30 deg C, the uart stops working. I believe that this is...
