Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I am trying to make my gateway send stereo data to the headset where it will be played on an external codec. I want this to be a single stereo stream.
I had this working...
Hi,
I was looking into hooking up an SD card to the nRF9160DK that I use for data collection during evaluation and early stage pilot projects. I noticed that there is an...
Describe the bug
BLE pairing on the new NRF54L15DK does not succeed. Connecting and advertising works, only pairing fails. I have tried the same example on the NRF52840DK...
Hi, we are using custom PCB with nRF9160.
we are writing a firmware for radio test lab. We are using LTE asynchronous in our firmware and LTE-M mode. We want the modem to...
Hello.
I am using the nRF5340 DK.
According to the circuit diagram, it seems that when I apply power to VBUS_nRF, there should be no power on VDD_nRF of the MCU.
(Power...
Hi,
for my custom device with nRF52840 and nRF Connect SDk v.2.8.0with VScode I want to add bootloader so that I can pass firmware to it through USB cable. I want a simple...
Hi, Good day!
I have been trying to change the SDK version for the past few days, but I am unable to open the Manage SDKs or Manage Toolchains tabs....
Dear Nordic Engineers
I used NCS2.8.0 to test the DFU function. As we all know NCS2.6.0 used the mcumgr-cli tool to send the fireware of the DFU image. But on NCS 2.7.0...
Hi, I am trying to understand how BLE data is fragmented and how I can send large amounts of data over BLE. I have log files that I want to send from an nRF54L15 to a mobile...
Hello,
in preparation to ask for support, I wanted to upgrade a project from v2.7.99-cs2 to v2.8.0. The project builds with v2.7.99-cs2 but reproducible fails to build with...
Hi Nordic team!
In our system, we’re using the GNSS functionality of the NRF91 to obtain the current time, which is crucial for synchronization across multiple stationary...
Hi,
First of all, let me confess I am new to NRF and BLE environment.
I am working on a project where the mobile device and NRF 52840 acts as a BLE peripheral and one...
Hi Team,
The command AT%XRFTEST (AT%XRFTEST=1,1,5,8300,17,1,1,6,0,0,3,3,0) result with ERROR
Any idea why
Tried with SDK 2.5.2 and modem 1.3.5
Tried with SDK 2.1...
I am trying to use RTT logs for debuging. I have no UART in my board. so, this is my ony option for debuing.
I tried it on my board and the nrf52dk/nrf52832 board.
I...
Hello I have a Periphiral bluetooth application which lets you communicate to it via shell commands. the service is compatible with NUS. when running the code with the 5.2...
