Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have a program working well in SDK 2.9.1 on nrf52840DK. I want to port it over to nrf54L15DK.
Please help me identify corresponding ports I can use on nrf54L15...
Hello, I've been working with a custom board using the nRF5340, but I’ve been struggling with picking up any BLE signal from it. I flashed the network core separately with...
I just got my custom board in and when the code gets to bt_enable it returns -11, but on the DK board it works fine (using the same board dts files and software for both)...
I am implementing DFU using my own transport to retrieve the binary image from AWS.
I'm developing in 2.6.0.
I am using the DFU TARGET libraries.
When I start my download...
Dear Nordic
I'm looking for a DTM code for nRF54L15,
From previous experience of nRF52,
There are some example HEX files available in SDK,
But I can't find any example...
Hi,
I have used the sample given in blog , however, my purpose is to get data from two device "IMU1" and "IMU2", using callback " static uint8_t ble_data_received " to print...
Hello everyone! :)
I have a problem with LTE connection. It worked for a few months; however, since a few days ago, the nrf9151 refused to connect to LTE. I tried with 2...
I'm building a system with onboard stereo speakers that can take a maximum of 1,4A when operating at low battery voltage. Can I safely bypass the npm1300 and directly draw...
I am using nRF Connect SDK 2.9.0 with Toolchain 2.9.0 and trying to interface Winbond W25Q32 SPI flash memory with nRF21540DK (nRF52840) . I need help with the following:...
Dear Sir / Madam,
We are testing with NRF9160 and building on top of k _uptime _ticks, I find the precision of the ticks clock to be ~70 ppm, while testing on my desk. According...
Hello,
I have been trying to figure out how to enable coexistence between Bluetooth low energy and the nRF7002 and I have some questions.
1. In the nRF Connect SDK documentation...
Using nrf5340dk, SDK v1.9.0
Want to add external RTC via I2C to wake mcu up via alarm, Facing Issue with I2C init.
I have gone through the suggested sdk fundamental course...
Hi,
When do you plan to update your Online Power Profiler Tool for cellular with nRF9151 device?
I just can see nRF9160 available for calculation.
Regards,
Hello,
I am working on an ESB (Enhanced ShockBurst) communication setup using the following hardware:
Receiver (RX): nRF5340
Transmitter (TX): nRF52840 MDK Dongle...
