Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
My Thingy:52 is version 1.01. I haven't used it for a while and after charging, it didn't seem to be advertising. It was soft-flashing a green LED. I decided to program it...
Hi,
i am working on nrf52dk. i want to include "pwm" example in "ble_app_uart" example . i have included all the header files. and functions in "ble_app_uart" example. ...
Hi,
what is safe temperature range for nRF52840 - nRF9160 UART communication on 115200 baudrate without external crystals for HF clocks please ?
Thank you.
Hi,
I'm trying to program a custom board with a nRF52810 via nRF Connect. I keep getting the following error messages:
I followed this post and tried the following commands...
Hey guys,
I have nrf52832 custom Bluetooth module. It is stand alone nr52832 module . I just want to toggle any gpio on this module .
Can you guys tell me which library...
Hi all,
In my project, I make 2 SPIM and 1 UARTE works well.
Currently I want to use 1 TWIM, so I add lines below in proj.conf
However, I get errors: gen_isr_tables...
If nRF9160 stay almost all day in sleep, wake via RTC for a period of 1 minute and in this 1 minute period only make a GPS cold start, get the GPS coordinates and transmit...
My device is the slave, that is being connected (not always in the same order) by 2 masters.
I would like to create two different connection ways/points to distinguish between...
Hello.
1. For nRF5340 DK, in normal voltage mode, I use putty(windows) and minicom(Ubuntu) to view the printk logs, it works fine.
In high voltage mode, which software...
I am currently trying to test the writable ndef message example on my nrf52 development board. I have gotten it to work so many times in the past weeks but now it seems when...
It seems like there is a problem with nRF Connect 3.7.0 with Toolchain Manager 0.9.3
When I try to open I get the following error.
I have tried restarting and reinstalling...
I'm having trouble connecting the Thingy:91 to LTE network.
I'm using the thingy91_fw_2021-06-28_7a076c22 example.
I flashed correctly the thingy91_asset_tracker_v2_nbiot_2021...
Dear Nordic team,
We are deveopping BLE & ANT enabled display. Because it is a mass production product we need to do an automation for asigning devices destinguesed ID....
Hi, Dev Zone.
thanks for help : )
i'm try to porting DK Board's ble Boanding function to Target Board.
DK is working success.
refer to 16.0.0 SDK and 7.0.1 Soft...
Hi,
I am currently working on updating the examples/dfu/secure_bootloader_uart_debug example in SDK 15.3.0 to do an internal dfu on my nrf52840 DK rather than having the...
