Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
We have been working with nRF52832 and using BLE Mesh in our product. The product is an Access control reader which scans for nearby smartphones over BLE and sends...
Module model: nrf52832
SDK: 15.2
Hi,
I am trying to add custom characteristics to a custom service.
There are two ways that I am aware of:
a. sd_ble_gatts_characteristic_add...
I have a firmware version present SDK 13.1 and S132 SoftDevice v4.0.5 I am trying to do a DFU (just SD+BL first) which now has SDK 16.0 and S113 SoftDevice v7.0.1 But my package...
Hello, I have a issue about flash_manager module.
When I load a program on processor (that has been previously erased) there is a problem with initialization (flash_manager_add...
I'm trying to get a temperature reading from the on-chip temperature sensor on the NRF52832 - I know it is not a very accurate sensor but I still want to use it. I found a...
With IAR (EWARM) 8.50.9 the UART project in the SDK compiles fine.
After upgrading to IAR (EWARM) 9.10.1 or 9.10.2 I get compiler error:
Error[Go029]: Variable "sec_mode...
Hi!
I'm trying to use a precompiled library of TVOC sensor ZMOD4410 in a project based on the azure_iot_hub from Nordic, running it over a nrf9160 board.
This library...
When I follow this tutorial and build the secure BLE bootloader example, I got this error:
cannot find ../../../../../external/nrf_oberon/lib/cortex-m4/soft-float/liboberon_3...
Hello,
I've been working on a big software project on the nrf52 DK with Segger Embedded Studio and added a lot of libraries and drivers. The issue I ran into is that if...
I am attempting to update firmware on hardware already in the field. The firmware in the field is based of sdk v11 and has the legacy bootloader for OTA DFU. After some digging...
Hello Nordic,
Due to recent shortages we have switched from a BLE module with external LF oscillator (uBlox Nina-B3) to a module without external LF (Laird BL654). We have...
Hello,
I'm currently starting to develop with the Nordic nRF5340dk and trying to build a mesh network but i'm having some trouble on the examples to understand and buld...
Hello guys,
I have some doubts in the examples you provided for BLE for mesh.
My questions are:
1. - In the examples of light_switch (server or client mode), the nodes...
My goal was to make a bootloader, that, when not requested, still goes do DFU mode for 5 seconds,
so that there is always an option to get to the bootloader after boot,...
