Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello all!
I have been modifying the door_lock_nus example to add the set pin command (0x05 from zcl reference). So I have modified the zigbee callback to read the new...
Hi,
I am wondering how to let these both run together. If I understand the sdk_config correctly the app_scheduler event queue can be used for the USB directly. But how should...
When performing a DFU the 2nd stage increments the expected device BLE address by 1 when the device being updated reboots. This potentially conflicts with the address of an...
We have developed a PCB using nrf52840 controller. It's a brand new controller. I am using SEGGER embedded studio for programing.
I have flashed an example code ble_app_blinky_pca10056_s140...
If one using nRF52840 microcontroller as non-RF one, in example configuration from page 593 / Figure 214, No 6 schematic, I have two questions
- does a ANT pin filtering...
hello Nordic
i am working with nrf52840 dev board, sdk 16.0, based on the peripheral app_ble_blinky example.
i have 2 spi comms, one twi, and use rtc, app timer and...
Hi,
I'm using nrf52840 and connecting to a mobile device via BLE.
After bonding connection, I'm restarting my nrf device in order to start advertising again, with...
Hello All,
I am new to this field and would like to know technical details of this field. I want to develop a product using NRF52833-QIAA-R7 or NRF52840-QIAA-T
Anyone...
Are there any examples showing how to handle MQTT QOS 2? I have searched for MQTT_EVT_PUBREC, MQTT_EVT_PUBREL, and MQTT_EVT_PUBCOMP and nothing shows up for any.
Hello ,
I am using NRF52 DK Board with SDK15.3.0 .
I am followed below tutorial for DFU update .
https://www.youtube.com/watch?v=c7D0dC2gANo
But , after loadfile command...
I am evaluating the PPK2 for use in a custom test bench. The test bench uses a few Python programs to gather current measurements of a device under different operating conditions...
Chip: nrf52832
SDK: 15
SD: s132_nrf52_6.0.0_softdevice
After connection, we request a new MTU size. Some values work, other don't.
For example, trying to get 187 bytes...
Hi,
The following command will not work:
> "/mnt/c/Program Files/Nordic Semiconductor/nrf-command-line-tools/bin/nrfjprog.exe" --family NRF52 --program "/mnt/c/Nordic...
Hello, we need some help debugging a proxy node in a BLE mesh network.
First some information about our experiment - we currently have 5 nodes running a custom fw on a nrf52832...
