I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
We have run the Hello World program on the nRF5340-PDK, but now following the basic steps to program the heart rate example, there is no BT broadcast for Zephyr Heartrate...
Hello everyone. I'm creating a setup function to configure LSM9DS1 accelerometer and gyroscope by writing to the corresponding registers as shown below
Although this code...
I use sdk16.0 and nrf52832.
Can you give me an example of nrf52832 timeslot example ? thank you.
I read timeslot on DevZone,but many routines are missing files, resulting...
Writing an app for the Arduino Nano 33 BLE Sense:
https://store.arduino.cc/usa/nano-33-ble-sense
Basically I am reading all sensors on the Sense board (temperature, humidity...
I have programmed a Nordic Thingy 91 with lte_ble_gateway, and when I send command from the cloud to the device, an NRF_CLOUD_EVT_RX_DATA event is called, however evt->param...
Dear all,
I want to implement multiple functions with only one power button, including: 1. Power on/off, Long press to turn on, long press to turn off; 2. Functional response...
I am trying to connect nrf52840 dongle to multiple peripherals(nrf51822) ,so far i combined multilink_c example with uart_c and i can connect and read rssi value of only 1...
Sorry, my English is very bad.
I think I can only express my problem in Chinese.
在使用异步串口时，使用uart_rx_enable()设置的超时时间和真实发生UART_RX_RDY事件的时间相差巨大
using async serial port...
Hi,
We need to interface camera (0.3nrf52840MP to 2MP) with nrf52840 for a new product development. For evaluation purpose, is there any off the shelf camera module which...
I'm trying to add a timer to the usb_cdc_acm example to send a periodic text messages with the timer. I'm building on an Adafruit nRF52840 Feather Express board using Segger...
Hi ,
I am trying to parse the manufacturer specific data that a beacon is advertising.
I can read successfully the company_id but unable to read the "specific data " ...
Hello again Nordic Pro's,
As you probably all know by now, our product app is based on the subject example code, SDK and device. We need to programmatically disconnect from...
I have been trying ti debug with SES and re-installed everything trying to get it to work, for a while it did, but then it began showing this message:
also, it asks me...
Hi All,
I am working on nRF9160 GPS profile. built the code with Segger version 4.16 and updated the latest mfw_nrf9160_1.1.1 modem firmware.
when i compile try to catch...
