Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello Nordic Community!
I have seen previous posts mentioning that the DFU example was not working with SDK 15.3 ( Getting started blog ). But in my case I was able to...
Hi all,
I am working on a new project and I need to communicate to a sensor using I2C, then save the data on a flash (files visible on windows as mass storage via USB) and...
Hi,
I am developing an application where the device should support both central and peripheral roles at the same time. My devices are connecting to a mobile phone. All the...
Hi, I use the nRF52840-DK together with a secure element (Infineon Trust X) and want to measure current/powerconsumption of this whole setup during certain operations. At...
Hello!
I'm currently trying to run the mqtt_simple sample (latest version of nrf-zephyr) on the nrf9160 DK. Unfortunately it is not working, because getaddrinfo() returns...
Hi,
I am using the nRF Connect SDK to develop software for a nRF5340_PDK focusing on Security and power efficiency. Therefore I wanted to make use of the CryptoCell-312...
Hello,
The release-notes of the Modem Firmware v1.0.0 for the nRF9160 state that there is now "Support for DNS server address setting by application.". However, I cannot...
After updating to nRF9160 mode firmware v1.1.1 there have been several vector catches. I have not updated Zephyr or anything else from the latest version downloaded on 9/24...
Hi,
I have programmed my Nordic Thingy 91 with lte_ble_gateway and seems to work fine. However whenever I increase the connection parameters, the thingy91 fails in the discoverty...
Hello All,
Please share me the link where I can get complete explanation on software part for how to use following wakeup options as stated in datasheet
1]The detect signal...
Hi all,
I have 3 nRF52840 Bluetooth tags and I have used Segger Embedded Studio for programming the nRF52840 for the proximity application. Once I have programmed all the...
Hi,
We are seeing some strange stuff when trying to pass floating point values to a function. When we pass the parameter by value (meaning as an actual floating point number...
Hi!
I'm trying to communicate with modem through UART.
Power supply: Battery connected to VDDH
VDD_nRF: 1.8V
nRF52840 DK connected to modem devkit using wires (about...
I am using example code TWI_sensor. It is the same code i just switch ports and added couple of lines that would power up my sensor. After running it i can't even clk going...
Dear Community;
I am using this code provided by a Nordic engineer to make some HTTP request in order to use Telegram Bot API . It works fine but after 1-2 days working...
