Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello, working on an incredibly frustrating problem.
We have a 2-chip system and the primary chip (non-nrf) communicates with the nrf52840 as a SPI master, and of course...
I'm using the NRF52832-QFAA-R and currently I'm struggling to get the device to connect to a J-link. The nRST line for some reason is being held low even with a pullup. There...
To the kind attention of Nordic support team,
I have got legacy code to work with for nRF24LU1. Radio packets payload and receiving pipe are retrieved using if(gzll_rx_fifo_read...
Hi, I am using nrf52832 Development Kit and SDK( nRF5_SDK_15.3.0_59ac345 ) in that I am working on ANCS and NUS together and specific functionality working smoothly when the...
I have read many of the posts about applications not running stand alone, and have tried many of the suggestions without success. My application runs on a nRF52832 it is being...
Hello,
I am new to embedded programming and I would really appreciate any guidance.
I am using NRF52832 that will interface with I2C USB charger BQ24295 ( http://www.ti...
Hello, I am working on Bluetooth mesh application and i am using nRF52832/40 for the development purpose. I wants to create one independent library with its own data section...
I need to burst write the DMP library into the mpu6050 but not succeed.
The following is the function that I've been using to burst write.
I have researched on the...
Hi,
We developed our device with KEIL 5, SDK15.2 and SoftDevice 6.1.1. After we upgrade the SDK on our device from version 14 to 15, our IOS phone encountered the following...
Dears:
I'm testing the USB mass storage example: \examples\peripheral\usbd_msc with Nrf52840DK and SDK v15.3.0.
Now I have one question. When I plug in/out USB to PC or...
Hi
I am using the NRF52832 ,my code is based on the ble_app_hrs_freertos example sdk 15.0.0
I have one main task which usually run 64 time every second using the vTaskDelayUntil...
Hi I have a module that is used in a hand held instrument. It contains the nrf52832. It connects to phones for data communications. Is it possible to determine the strength...
Dear All,
I am trying to compile and run the ncs/zephyr/samples/drivers on the nrf9160_pca10090ns. For this reason, I have copy-pasted the file under the ncs/nrf/samples...
Sorry, I want to ask that if I can send Decimal(like accel x,gyro x) by the ble characteristic to the nrfConnect, when I send the information, it always becomes hexadecim...
Dear community members
I have end nodes with nrf52832 (Soft device s132) that can communicate to a central nrf52832 DK in Connection mode based on ble app uart and multiple...
