I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
Hello, I am trying to create a clone of a temperature sensor with the nRF52840 DK. I catched all important data from the sensor to configure the nRF52840 DK. But I cant find...
Hello.
I am trying to implement a Zigbee Network were sensors will be posting data periodically to a Coordinator.
I was looking into the examples provided with the SDK...
Hi team,
Our customer use nRF52810 to be an RF dongle.
They meet an question was about the high PER when there was an headset dongle was near nRF52810 as bellowing....
Hi,
I had the issuse about power consumption of saadc.The current measured was always more than 500ua after I called nrfx_saadc_sample().My test code is below.
I am using nRF32 ble module. I am not able to get the value from BluetoothGattCharacteristic. I have declared an object of BluetoothGattCharacteristic and getting the value...
Hi everyone,
SDK version: 15.3.0
I read the DFU documentation and can't find the <InstallFolder>\examples\dfu\bootloader_secure_ble folder in SDK 15.0.3.
This folder...
Hi.
I have problem with dfu over ble with mesh sdk. I use example experimental_lpn as guide. When I add this dfu functionality in my project, my application is not responding...
We are designing a radio transmitter for a long range hobby craft vehicle with Gazell. We need to use frequency hopping as well as the pairing functionality that Gazell offers...
Hi,
I have few questions to be cleared before get into the nRF9160 to use in India.
As per the datasheet, nRF9160 supports LTE CAT M1 and NB1/NB2.
Can I be able to use...
For Above case i am planning to interface with U FL to SMA cable for external antenna interface. nrf9160 ant pin and U FL connector will be routed using 50 E impedance. at...
Hi,
I have found an interesting behavior from this code:
nrf_gpio_cfg_input(7,NRF_GPIO_PIN_NOPULL);
if (nrf_gpio_pin_read(7)==0)
{
NRF_LOG_INFO("ID1(P0.%d) is LOW...
Hi,
I am developing the proprietary protocol by using ESB function in nRF52832.
If the linear distance between the two devices is less than 10 cm, normal communication...
Hey! I am very new to the NRF52 environment, and have just started tinkering with the BLE capabilities. For my project I need to send 5 Kbytes of sensor data as fast as possible...
Hey.
We use the same SPI bus for accessing an external flash memory and gyroscope device (Bosch chip).
We encounter a problem regarding the SPI when performing the...
I´m running on NRF52840 with SDK version 15.2.0 and trying to use atfifo, and I have observed a bug when writing to the atfifo buffer twice and then reading from the atfifo...
