Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
running DFU example from <SDK 15.3>\examples\dfu\secure_dfu_test_images\ble\nrf52840 , and attempting a DFU update of:
sd_s140_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi everyone.
I have a problem with processing with recived UART data. I'm using software UART from example > peripheral > uart.
I use nRF to comunicate with GSM module...
Hello,
how can I store CCCD values in flash?
I read that the peer manager handles it ,but when i reset my device and load all bonded peer data, the CCCDs are not set....
Hello everyone,
i'm trying to hook up an external i2C sensor to P5 connector (TWI_SCL_EXT, TWI_SDA_EXT) and created a device driver template ( from drv_gas_sensor.c example...
What is the max amount of data that can be saved in records in fds?
When we do a dfu, is the data conserved or not?
How to vary the size of the records if possible?
...
Hi all,
Recently, I have concentrated on a mesh project using nrf52840 board programmed sdk_mesh_v_3.1.0. There is a situation that the board needs to send two different...
We have a project to explain the company Shenzhen Zhouhai Technology Co. to invite them as our partner because we see the smart bracelet CK series would be a good option for...
Hello,
We're using the UDP/IP/6LoWPAN layers as provided by the nRF5 SDK 15.0.0.0.
After experiencing sporadic issues in communication we have a question regarding the...
Hi,
I am using BLE_Blinky_Peripheral example from SDK 15.3.0 with s112 softdevice. I want to use basic softdevice APIs instead of nrf_sdh libraries for enabling BLE stack...
I am a beginner trying to get a device to operate optimally under a battery. Where can I find a starter code template that would shutdown/disable everything, putting the device...
Hi there,
I am working with the NRF52840 Dongle and have been trying to verify what sort of influence other processes on the chip could have on the radio. Specifically,...
Hello Nordic team,
I'm having some trouble with discovering the characteristics of a custom device.
The peripheral device has a private service with UUID 06000002-0000...
I'm busy implementing a (serial) DFU host, but sofar i'm unable to send a proper init packet.
The bootloader keeps returning an invalid signature error
If i open a .dat...
