Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
hi....
i am facing the problem , after debugging the program is not running,run option is disable , i couldn't able to do start code execution .. see the pic below
i am...
WIN10.
This is step #1 .. the 85840s are not showing up in file explorer. They did months ago, but with all the WIN10 updates and other IDEs (atmels) being loaded, something...
I am using SES 3.52a with SDK 15.0. ( I have a program based upon SDK14.1 from a year ago that was my starting point.)
In my current environment, my Debug config builds...
1. As a slave device, how do I update the content of a feature value when I set a feature value to the property of read? 2. The local setting can set the data of the feature...
Hi I am Working On Nrf Beacon in nrf51 Dk with the SDK11.
I am Trying to changing the name Of the Beacon ,,but i am not able to do this ..i want to change the name as well...
Hello,
I got a NRF52840 and want to use the BLE S140. On the application I want to use the CC310 random number generator.
- The S140 specification states that S140 uses...
nRF52 DK, PCA10040 v1.2.1
PPK PCA63511 rev 1.1.0 2018
I am connecting the PPK to the NRF52 DK in the simple case where I want to measure power consumption of the 52832...
I'm trying to get nRF sniffer to work in wireshark. I followed all the steps from the nRF sniffer user guide, but I can't get it to work.
The issue: - when I have the PCA10040...
Hi,
I tried to build your own example about "fatfs" on my board "nrf52840pdk" ( with MyNewt as OS ) but it seems that "ff.h" can't be found. Has it got any dependencies...
An nRF5 SDK for Mesh v2.2.0 dimming example client running on a nRF52840 Preview DK is not detected for provisioning by a nRF Mesh smartphone provisioner.
Running the example...
I am in process of doing my eng. thesis and apart from setting up Thread network part of my work is to measure delivery time of messages.
For now I have an application based...
Hello!
I am using NRF51822 in receiver mode with enabled interrupt on ADDRESS event, and even if transmitter is switched off I still get a few messages every second. It...
hi........
i have customized one program ....using segger 15.2 ...nrf52832
when degug it,the code from button and leds stops at nrf_breakpoint_cond ... even it doesn't...
When performing pre-qualifying Bluetooth radiotest of our hardware (utilizing the nRF52840-chip) at NEMCO, we experienced very strange behavior. The frequencies detected in...
My setup of the buttonless BLE DFU secure bootloader using SDK15.2 isn't launching the application after a successful OTA package transfer. Using RTT and breakpoints, I narrowed...