Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
there seems to be a bug in the Heart Rate Monitor (HRM) example or in the iOS app (nRF connect) -- when the simulated heart rate exceeds 8 bits (256) in the example...
I need to send data to an APP through NRF52832/840
This data will only be sent when there is a match with my APP. Once I have established a first communication with my APP...
Hello!
Hello, I have an Issue with NRF51822 chip, made an over 25k messages per second transmitter based on Keil example, but the main difference is that I dont enbable...
Dear all,
In my project, I add 3 long push action events related to 3 buttons by using " bsp_event_to_button_action_assign( )". Everytime I long push any of 3 buttons, the...
Hi,
I am trying to program the bootloader for the nrf52840. I am trying to create a settings for the specific hex file, and then programming using the nrfjprog commands...
Hello,
I use a custom board for an IoT application. The BLE module I use on this board is Taiyo Yuden EYSLCNZWW which uses nRF52810 and requires softdevice s112.
I already...
Hi all, I've been testing 6loWPAN over BLE with the nRF52 DK ( nRF52832) using the IPSP sample code from Zephyr OS, and have managed to successfully flash the code and establish...
Hi all,
I have a Raytac MDBT50Q-DB board which I was programming using an nRF82540-DK. It all used to work fine, but now JLink cannot connect to the Raytac board anymore...
Hello,
I'm using nrf52 DK with SDK 14, to flash a Taiyo Yuden EYSHCNZWZ module ( Module Datasheet ). The flashing is successful, as stated by the output console in Segger...
I am a master student. I am working on a project that uses Bluetooth 5 Beacon Scan.
I bought the nRF52840 dongle to scan the Bluetooth 5 Beacon
I want to scan the Bluetooth...
hello!
I am currently using SDK14.2 (migration to 15.2 WIP) and S132 and on a custom board
requirements - I want to collect data from around 50 (or more) PERIPHERALS...
Hi to all,
i am developing a device with NRF52840 soc and i am using cryptocell IP to create ecc key pair. as you know public key of an ECC alg is a point on spec curve...
Hello All.
I am using the following
SDK Version : nRF5_SDK_15.2.0_9412b96
Segger Studio Version : 4.10
Mesh Version : nrf5_SDK_for_Mesh_v2.2.0_src
I am trying to...
Hi,
I am woking on NRF52840.
OS : Windows
SDK version : 15.0
Dev : Keil IDE.
I am using Timer -2, Compare value method to obtain an interrupt.
The interrupt...
The thing I currently try to implement is to combine two 128-bit services in one app - custom and UART.
I arleady made run them separately - one service at app.
Way they...
