Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Here NRF52 TX pin is connected to Battery to measure voltage Level. i am using NRF52 with SDK 11 and s132 soft device.
Here is my Schematics
here BATTERY is connected...
Hi
I am working with the twi_scanner_pca10056 example found in the SDK. Using a oscilloscope I can detect the logging messages on pin P0.01, even though sdt_config.h defines...
Hi all, when I modify ble_central for connect multi peripheral via NUS. I got error : BLE_DB_DISCOVERY_ERROR in funtion
So, can you show me how to solve it . Thank very...
Hi there,
Is possible use nrfjprog to write in flash the data time using windows batch commands after programmed the device?
actually, I want to use the nRF52 as a RTC...
I have a question about the nRF52840 QIAA Reference Layout v1.0 which can be found in the infocenter /nRF52 Series/Reference Layout. I saw that it has keepout areas on mid...
I'm trying to implement an application for the nRF52832 that will provide an OTA update to another external nRF52. The code for the device accepting the update has already...
HI, i want to know, how can i use the feature of LE Data Packet Length Extension which in core v4.2.
i want to connect the PDK with the my phone, What should we change?
I want to establish a BT network system which includes one pc as a central node, and 32 client nodes. I want to collect 32 client's sensor data concurrently via BT. At pc...
Hello I was trying to run the Power Profiler Module with nRF Connect but I geting the following error:
ps: The python solution is already working for me.
What is the RTC run current on the nRF528120? It is not listed in the datasheet.
In addition, what is the run currents for the clocks on the 810? There is no information...
I need to send data from PC (windows 10) to nrf52832 using UART (hardware) in order to retransmit this data through mesh network with light switch example.
Do i need to...
Because I'm using PTR9618 module of nRF52832, it don't have XTAL 32.768Khz (X2).
When Makefile have NRF52_WITHOUT_SOFTDEVICE=1, hello-world, blink-hello work fine. But when...
Hi,
I'm looking to generate a clock signal on a gpio with an exact frequency. I tried this by setting the pwm base clock and adjusting the top value but got no luck.
Is...
Hi Nordic,
I find somethig wrong while using GPIOTE.
I.
First I call nrf_drv_gpiote_out_init(MY_PIN, &my_config), it works fine. However, I call nrf_drv_gpiote_out_uninit...
