Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello, everyone.
I am using sdk v17 and I am looking into timer. I used the app_timer simply, but I don't know the nrf_drv_timer because I've never seen it before. Can...
I am a beginner who just bought nrf52832 dk and started !!
I am trying to control the pressure sensor, gyro/ accelerationsensor and motor,
but i ts not easy because...
I'm trying to build a quick application to scan for all devices in the vicinity and print out their details (device name, manf data, RSSI, and BLE address). I am parsing the...
According to BLE 5.1 Core Specification Coded PHY and CTE are mutually exclusive. But losing 4xRange to implement Direction Finding is a big loss if, for instance, you need...
Hello,
I used the examples\peripheral\libuarte example to implement a driver for NBIoT DCE. I embedded the sample in my project and started debugging. Although the transmitter...
I got an error at pc = 0x104F0 (id = 1, pc = 66800, info = 0). My code is advertising and doing nothing else except a timer for the LED flashing, so I'm not sure what could...
HI
I am using the customized nRF52832 board with a temperature sensor connected via i2c .Firmware i merged the ble_app_uart and twi_sensor xample code. Here the RX AND SDA...
Hi everyone,
I've written a custom BLE service with two characteristics. I want to write more that one bytes to one of the characteristics and then to store the written...
Hello,
I'm working with nRF52840 and SDK v15.2.
I implemented an USB layer with CDC and MSC classes based on nRF examples. All seems to work fine. The USB Serial port...
Hi,
I am using TPS61021DSG in my design which is a data acquisition system using nRF52832 BLE module. I am using 1.4V Zinc-air battery to power up my circuit to generate...
Hi Nordic Team
I want to run the example project[802_15_4] on the soc chip 52820.So for the SDK17.0,it run and work well on soc chip 52840.
In order to run on the chip...
Hi,
I am using an Adafruit nrf52840 Feather board and have been having a problem with SPIM instance # 3.
I have the board connected to a display module and have been successful...
Hi,
This is not a ticket!
This is a project that I built. It uses the nRF52 to control a neopixel (ws2812b) via I2S over BLE using a custom mobile app built using the...
On SDK16.0.0 + Mesh SDK 4.1.0
I know that oversampling when using the SADDC in scan mode on multiple channels does not work because the buffer gets all out of order.
But...
