Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
We are looking for a guideline to trigger GPIO and SAADC sampling at the same time.
Our purpose is to sample every 20 m
Hi,
We are looking for a guideline...
Hi, We have a DFU OTA process that was functional, but updating our softdevice to s113 7.2.0 has left us with a problem - since the softdevice does not exist in the nrfutil...
Hello.
I am doing a small project where nrf52 reads data from a BME280 temperature sensor via SPI and sends it using ESB.
I have no experience with radio, so I use a ready...
I would like to use the NRF24L01+ from a 3v coin cell, but interface it over SPI with a 1.8v-powered microcontroller. Assuming the uC is tolerant of the NRF SPI outputs, I...
We have a application where data transfers happen through a mechanism where the external client does a write-without-response to send in a command. The response to the command...
I am busy with my first BLE project , programming a custom service for both pheripheral and central role. I have already finished the pheripheral service, using a custom service...
There are other GPS modules on the market which can give information like "the device is within 10 meters of the given coordinates". Is there a way to either get this information...
Hello,
i am using AES CCM encryption available in nrf52832,
my data which need to be encrypt is same every time. data will encrypt and 4 byte will add at the end of...
Hi all,
I am working on a project with the nrf52832 and I am using softdevice S132 6.1.1. After creating my desired flash layout (with some help on this forum, thanks!)...
Dear,
I am using NRF52840 and nRF5_SDK_17.0.0_9d13099 and SES development tool.
And also, I am testing SPI master with p0.29/30,31 and P0.26.
but when I do "nrf_drv_spi_init...
I am tring to DFU by Bluetooth with example, but it not work.
Please someone help me!!
My environment
PCA10056 nRF52840
SDK17.0.0
examples/dfu/secure_bootloader...
I was working with the Thingy:91 trying to get into into a serial printing state. I tried to updated the modem and firmware using the nrf Programmer. When updating the modem...
I've been having problems trying to get any of your example project to use NLOG to a uart port that we have made available for production test on our new product.
I've chosen...
Hi,
I am desperately trying to read some RTT Input with Zephyr, but I just cant get it to work!
All I want is to read the RTT Input. I tried with the console and the shell...
Hello,
I am looking at the nrf52840-dongle to explore Bluetooth audio (in headset mode).
So - just to double check:
(1)
I assume I can interface to bluetooth audio...