Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
I am trying to learn free rtos on nrf 52dk. My doubt is how do we debug, watch tasks. I am using segger embedded studio IDE. for sdk, sequential execution of code the...
Hi
The nrf9160 product specification v2.0 changed the current consumption for UARTE from 1.5mA to 819.2mA. Revision history does not mention this hilarious change explicitly...
Hello Nordic Team,
i'm trying to configure the nRF52833 DK to scan through two channels at a high rate (10ksps) with the SAADC module. i have configured the time to operate...
Hey everybody,
I go sell my product in Morocco, my product is based on nRF51822 but I need to know the certification of electromagnetic compatibility for Bluetooth Low...
HI,
I tried to test all projects, but I ran into a problem， project create like this
I just downloaded the routine and didn't change anything， but I cannot create advertiser...
Hello
I have several questions regarding the RESET pin used in your examples:
When you press the RESET button of the PCA10056, is it possible to add code before it does...
I combined SAADC into the ble_app_uart_c example and got error once it got to scan_start();
"ble_scan: sd_ble_gap_scan_start returned 0x9"
If I put the scan_start() in...
OOB can be used to assure physically that the device provisioned is the wanted one.
In my application the devices won't allow for OOB.
How can I ensure that only my...
Hi,
I used this user guide: https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf .
I am using the nRF52840 DK for the sniffer, and managed to connect it and...
I changed the IO of the SPI and could not receive the data.
Hardware: nrf52832 DK two
Software: nRF5_SDK_17.0.2_d674dde\examples\peripheral\spi and nRF5_SDK_17.0.2_d674dde...
Hi,
I'm developing an application for the nRF52840 that uses 3 SAADC channels. In particular, the channels are configured as below:
I'm able to get the samples from...
It is unclear, for both the Thingy 91, version 1.0.2, and nRF9160-DK, version 0.8.3, if they need bias-tee's for use with an external active GPS antenna. Also, what about...
Hello, I have problem and I hope you can help me.
I have 3 sensor nodes. every node has an IMU sensor and nRF52840 microcontroller. These nodes send the IMU data to the...
We bought 4 NRF5340 PDK and trying to setup BLE mesh. As suggested in the getting started guide, there are two BLE mesh example samples from nordic and zephyr. However, for...
