Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
So simple question about adapting dev kit examples for the dongle. I'm trying to adapt this USB/BLE example and I've made all the changes that I figured I'd need to...
Hello,
I'm currently levelling up a project based on an older SDK which involved SoftDevice v5 (S132) to SoftDevice v7 (S140).
As far as I understand S132 and S140 are...
Hello,
following the peripheral/saadc sample, which shows the periodic reading... could you please share the essential and minimal config for the One-Shot measurement? ...
I want to integrate the XMOS (XUF216-512-tq128) with nRF52840 where the nRF can be used to perform the field updates for the XMOS. Is there an application note or an example...
hello,
i am using nrf52832 device with soft device of S132.
i am trying to connect 2 different applications on the same smartphone to the peripheral device. currently...
I have two NRF52840 dev kits that are running what are essentially the spi master and spi slave examples. They both work and I've altered them slightly. I'm just kind of confused...
Hi,
I've been trying to combine the spi_slave and USB_CDC_ADM examples so that I can pipe data from a spi_master all the way to my host machine. In my cobbled together...
Hello ,
Is there any development KIT available for the Evaluation of Direction FInding - AoA and AoD ? Any code examples for the same?
If not what is the time line?
...
Good day,
I would like to switch between two states once I receive a trigger. state1 <---trigger--->state2.
State1 = Beacon/custom manufacturing data - Beacon Example...
Hi,
In my application after some timeout i am trying to stop BLE advertisement.
for this i am checking current connection state,If it is connected or disconnected.
if...
I'm using the TWI_MNGR to schedule a transfer. I have copied the nrf_twi_mngr_perform() function to a function called nrf_twi_mngr_schedule() which does everything except...
Hi team,
I am working with the nRF5340 PDK v0.8.0 and I am trying to request the additional voltage for the VREGRADIO to support the additional 3 dB TX power on the RADIO...
i have a project with Nrf24, i'm using NRF24L01 + PA LNA 2.4Ghz with athena, to get 1000m -2000m range.
But i saw on nordic website that nrf24 not for new design, we have...
I have seen a few references to SoftDevice in the 6.x series not being able to transmit at 500kbps in these forums, but I can't find anything in the docs to reference. Can...
Hi, I am using nrf52832 dev-kit. I use P0.23 or P0.24 as an input pin. I am trying use this pin to read data from other device. When I use this pin like button, it can detect...
