after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello, I am developing a system where I have a app and a Rigado BMD-300 Module. I am using, for experiment, the nRF Connect App and in program, I use SDK 14.2 and s132 softdevice...
Hi to everyone,
sorry if this question will result stupid, but I'm really new on programming Nordic microcontrollers.
I'm trying to develop a simple ble application for...
1. Did secure BLE DFU first time for hrs app, BL jump to hrs app
2. Did secure BLE DFU second time for hts app, BL jump to hts app
3. Did nrfjprog HID keyboard app and...
Hello,
I am using NRF52840 board and SDK 14.1, Softdevice 5.0.0-2.
I am testing other devices on my board. However, it seems to work normally until 2, but the connection...
Hi,
I just try the new mesh SDK V2.0.0. And I found that there is an error if I compile the "examples\light_switch\proxy_client" more than one time.
The error is here...
Hi,
I have successfully flashed nRF24LU1+ via ISP. Right now, I am validating using USB to download firmware for future production. Here is the issue.
Our project has...
Hello all,
I'm currently working on a project with a due date coming up soon. I'm using two (2) nRF24L01's with a nRF24L01+PA+LNA shield.
Right now I have my micro controller...
I want to change the advertising data of the advertising packets with time. I did find the solution for the same in this link - https://devzone.nordicsemi.com/f/nordic-q-a...
I have a board with an NRF52832 and an LED driver. I wrote a function that bit bangs a serial stream to an LED driver. It works when I use the nrf_gpio.h library.
However...
I am working with NRF 51DK. I am trying to flash a software on the target device which uses NRF51 microcontroller. I am using NrfGo studio. I am facing an error that, Unable...
Hi All,
I am newbie with nordic, and I need some help.
I am using nRF52832 with softdevice.
I need to generate a 128 kHz clock signal (PWM pulses with 128kHz frequency...
Hello, everyone!
I am a newbie developer about nrf51.
I need to advertise my BLE and save my power.
I have read the document that nrf51 has System-on (including some...
We have a couple of development units that are showing the above error in the nRF Toolbox app. Using the nRF Connect app, the DFU dialog just goes away and the screen reverts...
