Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi Nordic Engineers!
we bought 110 nRF52840 IC's for Field tests.
10 of them marked Q1AAAA / 1716AK
another 100 marked Q1AABB / 1745AC
What is difference between series...
Dear Nordic Team,
Thanks for supporting.
Now i am work with secure dfu using SDK12.3.0.
My Hardware :PCA10028
nrfutil version 3.1.0
Create Zip file like : nrfutil...
Hello.
I want to design a product. It will have these features;
It has 4 buttons on it.
Obviously it is battery powered device.
I want to see some information...
Hi
I have made ble scanner using nrf52 and I have set uart baud rate 921600 and sending scanned beacon to other micro-controller for processing but It does not scanning...
Hi
I'm looking for an example on how to write a hex-file to SoC using nrfjprog.dll.
The P/Invokes are all set and working fine.
I'm absolutely not familiar with python...
Hello,
In our project we want use a large characteristic with notification property.
I use a " ble_app_template " project from nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral...
I am working with the nRF52 DK, using SDK v14.2.0 and SoftDevice S132.
After removing all BSP functions from the BLE UART example, I am setting up LED1 and LED2 of the...
Hello,
I'm trying to get the FDS to work, but it's giving me a headache. I'm using SDK 13.1 and S132 4.0.2 on a NRF52832.
In the beginning I thought I had that issue...
Hello,
I am trying to figure out my problem related to this question .
I am writing just a couple of words to flash with FDS. The problem is that after writing, the...
I am trying to use nfc_t4t_lib in NFC_T4T_EMUMODE_PICC mode. After receiving an APDU I am doing some calculations and sending reply with nfc_t4t_response_pdu_send. If calculations...
What is the best way to store the values of my attribute data?
With my current code, from the tutorials, the read, write and notify works fine.
But I need to store the data...
Hello
I noticed that since S132 v3.x.x we can configure the MTU. Does all the posts referring to long writes in this forum apply to the situation before this feature ?...
Hi
on nrf52832 ble_app_uart how can change MTU size and LL payload size?
have any source ? or example ?
or any change MTU and payload example ?
( for BT4.2 ~ BT4...
Hi,
I'm using SDKv14.1 on nRF52810. I doing the DFU according to the ble_app_buttonless_dfu example. When I use sd_ble_gatts_service_add to add service UUID in the ble_dfu_buttonless_init...
