Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I have an application which requires the firmware to be updated on the field. In our device the embedded microcontroller Atmel 328 is connected to nRF52832 through...
When programming the bluetooth mesh light control demo example found in the bluetooth mesh SDK, i get this error using J-Link RTT Viewer:
0> <t: 0>, main.c, 116, -----...
As I know, I need to do watchdog feed on bootloader.
but what If watchdog reload value is long enough for DFU?
for example, if DFU via BLE takes 2-3 minutes, generally...
Hi,
I am using IAR embedded workbench IDE - ARM 8.20.1 (full version) to compile the SDK 14.0 blinky_pca10040_s132 -nrf52832_xxaa example. However, I got some errors which...
I'm currently using nRF Connect (windows), in conjunction with the PCA10028 board, as GATT server so I can provide a default test service to be consumed by other devices under...
Hi
An unprovisioned device will advertise a beacon and the spec says that it shall be advertised with non-connectable and non-scannable undirected advertising events
...
Hello there,
for a project I would like to use the Arduino Primo core with the nRF52832 chip to read a NFC Tag.
I could not figure why it can´t read a tag even though...
Hi,
I've test the light_control example with the PCA10028 & PCA10040 recently. The PCA10040 was test and it works normally, but the PCA10028 does not.
I have also checked...
I am working on an application that allocate data dynamically at initialization, and my malloc/calloc returns NULL a lot earlier than I expected.
Using a debug macro, I...
Use the E: \ Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart \ pca10040 this routine
Run to chart a breakpoint on the resumption of here
...
Hi guys,
I'm trying to use the HFCLK to generate high resolution timing. Ideally at the millisecond resolution. I've written a layer around the nrf_drv_timer.c module....
Hi,
I followed the tutorials you made to start developing BLE applications for nRF52 series development board. Then I started to make my custom application (in fact, it...
Hi everyone,
I have been reading the Specifications of Bluetooth 4.1, mostly about Universally Unique Identifiers (UUIDs) for Services, Characteristics, etc.
I found...
Respected sir,
setup for programming = Eclipse-gcc-toolchain-setup
board = PCA10040
as per my way first take a ble_app_uart code startup my coading purpose.
then we...
Hi Guys,
I'm doing the following before putting my device to sleep. This works fine when I use NRF_POWER->SYSTEMOFF, but when I use sd_power_system_off(), it doesn't seem...
