Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
I’m developing a project on the nRF52840 that uses BLE + RTC + an SD card. It’s based on a previous project that only used BLE + RTC, and I’ve added the ability to store data...
I'm trying to use a Power Profiler Kit II with a Mac running Ventura 13.7.8. If I update the Power Profiler App to v4.3.0 or v4.3.1 the PPK II is not detected and this is...
Dear Team,
I am using NRF54L15 DK, where I have UART defined and mapped as following:
uart20_default: uart20_default {
group1 {
psels = <NRF_PSEL(UART_TX, 1 ,...
I'm struggling to obtain stable ADC readings on the nRF54L15, and I'd appreciate any suggestions. I have the ADC configured with gain = 1, internal reference, 10 bit resolution...
Hello,
I'm trying to get a TIMER triggered ADC read on P1.11 AIN4. Sample advanced_non_blocking_internal_timer sounds like what I want but it isn't NRF54L15 compatible...
I am designing a very-low-cost device based on the nRF9151 and would like a quick technical clarification.
My plan is to power the SoC and all GPIO rails from a single 3...
I'm working on a project were we require the use of a custom OOB key (not generated by the device itself) and LESC.
We have both the central and peripheral device to configure...
Hi ,
Our nRF52840 chip is drawing a high-current burst of about 1.5 seconds during the DFU upgrade. Because we have a 10 mA current limit on the battery, the system browns...
Hi
According to the errata at https://docs-be.nordicsemi.com/bundle/errata_nRF21540_Rev2/attach/nRF21540_Revision_2_Errata_v1.2.pdf?_LANG=enus, a 33k resistor is required...
Hi,
I'm using nrf52840 in revision 3, which has protection access port enabled by default.
My application is built with SDK15.0.0 / SDS S140 6.0.0
In order to get debug...
Hi,
I would like to receive notifications from iPhone to nRF54L15-DK over BLE. Anyone in the nRF community tried iOS notifications over BLE to tell me how it is done please...
Hello,
Current Situation
We are working with an nRF5340 device running nRF Connect SDK v2.7.99-cs2 . BLE security is configured for Just Works pairing (Security Mode 1...
Dear Nordic Team,
I am using NRF54L15 on NRF54 DK board and when trying to use/activate any other UART other than UART20 (e.g. UART21, UART22, UART00) on my project, every...
Hello, I've been developing an nRF52840 on a custom PCB for ~1 month now, and my environment was working previously. After updating my version of Jlink and installing other...
