Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello all,
I have trouble reading saadc data with an amplitude of 10 µV - 100 µV with a sampling rate of 1K Hz by using nrf52832. I was wondering if I could get advice/help...
Hi,
The code is working normally, but when I include ble_radio_notification_init functionality. Then it crashes (hardfaults), on some boards not all.
[19:18:40.550]...
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). SES used Printf as a comment display and output it to the Terminal Emulator. I...
I've previously used Getting Started Assistant to install nRF Connect SDK 1.5.0 on macos and managed to get a complete and functional install.
I'm now trying the new Toolchain...
HI,
I have few queries regarding nRF52805.
Is there any specific pin configuration required to enter nRF52805 in to programming mode?
What is Adverting connectable...
Hello. I am conducting experiments with data transmission via the Enhanced ShockBurst protocol with BMD-340 modules. Transmission parameters: 2 Mbit radio channel speed, 512...
Hello Sirs
I want to use the serial port of nrf5340-Dk to get some serial data from a sensor and transmit this
data Via a peripheral connectable config by nrf5340-Dk ...
I'm trying to access an SD card with FAT_FS, with no success. I hooked an analyser to the SPI, but it's completely dead. I'm using NCS v1.6.0.
Is there something...
I am very new to BLE development, and am building my application on top of the ble_central\ble_app_uart_c example.
I have this tag defined at the start, with the other global...
Dear Nordic Engineers
Our customer uses NRF52810 with a PA chip, the model of the PA chip is RFX2401C. The attachment is the manual of the PA chip. The hardware connection...
Dear Nordic,
We use CONFIG_BT_CTLR_DATA_LENGTH_MAX definition set to 251 in our project to be able to send large data packets. Still, when migrating to nCS 1.6.1, we've...
Hi, Nordic team!
I want use RTC with Prescaler 32765 for generating Tick event with 1s interval. Could you help with calculation of jitter for Tick event in microseconds...
Hi,
I need to reduce the consumption of the peripheral_uart sample on a nrf5340dk, I use nRF Connect SDK V1.5.0.
At the beginning, I measured with an ampere meter 591uA...
When I program my external board via the nrf52dk the programming is much slower then when I program the nrf52 chip on the devboard. Is this normal behaviour and if not how...
Hi,
I'm evaluating a wireless microphone scenario, using 52's I2S and external ADC chip to sample sound signal, and than wirelessly transmitting it to another 52 for receiving...
