Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
i want to use orientation interrupt of bmi160. but i don't know how to read interrupt data. I wrote it after looking at the data sheet, but I want you to let me know if there...
I'm trying to get Thread working on the nRF52820. It seems that neither the "nRF5 SDK for Thread and Zigbee" nor the "nRF Connect SDK" support it (yet?), but instead require...
Hi,
I understand that when a peripheral is advertising it is also waiting for connection/scan requests.
Does those requests and responses sent via the same advertising...
Hello!
I'm trying to send a mcumgr packet over uart between the nrf9160dk_nrf9160 and the nrf9160dk_nrf5284.
To do this I have a SMP srv and a shell on both MCUs.
...
How do I get following combination to work:
Nrf connect 3.6.1 power profiler with PCA10040 v1.2.1 + PCA63511 v1.1.0 with external power supply and external DUT
The same...
My error messages in Segger studio are messed up (shown below). Everything else is fine. Can I change the font or something?
[m[K'[01m[Kdev[m[K' undeclared (first use in...
Hello, I have a 52832 using SDK16.0.0, that acts as an advertising peripheral (anyone can connect to it), and as a central, connected with 1-1 bond to a peripheral (a 52811...
Hi, using the Nordic power profiler 2 (PP2) kit to measure the current draw of my nRF52833 DK. I have followed the instructions to setup/prepare/wire the PP2 to my DK and...
In the task, when I do a TWI read via nrf_drv_twi_rx(), in the second iteration of the thread, the driver function returns NRF_ERROR_BUSY.
Is it that the driver takes longer...
I've built a custom board using nRF52832 which uses SDK 16.0.0 and softdevice version s113. A part of application is audio streaming/ decibel calculation and transmission...
Hall Mr. Nordic,
I'm sending a 16bit payload with 51822.
The receiver 24L01 is receiving all perfectly. The receiver 52840 is loosing the first two bytes ...
nRF51822...
Hi,
I'm using nRF52840 as my server and the android mobile is my client. At the client end, I'm using the nRF Connect app. It seems like the 50 bytes of data is taking around...
Hello,
I have an nRF9160 DK board (I believe the version is PCA10090 1.0.0) and would like to use the external flash that comes with this board.
Upon inspection, this...
Hi,
I'm seeking help on debugging the network core with Visual Studio Code. My project is not based on a standard SDK and hence I think VS code will be easier to setup than...
