Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
Two (2) nRF52840 DKs, SDK 17.0.2
I believe I have added the necessary code from ble_blinky_apps both peripheral and central to their respective NFC reference role examples...
Dear Sir/Madam,
I'am new to segger embedded studio.I would like to do SPI interfacing of an IC using nRF51822 with segger embedded studio.
Please guide me how to add...
Zephyr version: 2.4.99
OS: Linux
Board : nrf9160dk
I am trying to read data on UART 1 with interrupt. I have below shown portion in my code for enabling UART 1. (I...
Hi, I need to Interface the 2.4" SPI TFT Module ILI9341 Driver with nRF52832
I came across that in Peripheral/ GFx Example will run. once I build and run the project My...
Hi Dev Team,
I was working on the Nordic Thingy91 and had to establish an external communication of a sensor to the Thingy91 through a UART.
For this, I was looking into...
Hi,
My PC is Windows 7 64-bit and my tool is J-Link V9. The CPU at my target board is nrf52840. I use nRF connect desktop version 3.60 and it works fine. I got the upgrade...
I have the driver setup like all of the other sensor drivers I'm using, but I can't seem to find a device tree or Kconfig
This should be enabled by the CONFIG_SOC_NRF52840_QIAA...
Hello!
We have a custom board connected to a battery and a USB cable
Our fw calls:
NRF_POWER -> SYSTEMOFF = 1 ;
The board turns off.
And then we remove the USB...
Nordic's smart remote 3 is for nrf52832 and nrf52810.
I want to port the same on the nrf52840 DK.
I have basic IR receivers and Transmitter and want to integrate them...
I'm using the nrf52832 from fanstel (bt832) to stream audio to the adau1701 dsp. I want to be able to play music over Bluetooth. I'm using i2s to transfer the data to the...
Hello,
I am trying to change PHY after packet sent/received (known as asymmetric PHY).
After receiving EVENT_END, i write to register MODE to change the PHY.
This can...
Hi ,
I am using saadc to measure battery voltage i m using the sample example given as reference ble_app_proximity/
I am doing adc_configuration in one file and triggering...
Hello
I am starting with nRF 9160 DK and Segger Embedded Studio, I installed Segger through toolchain, the activation sim, updated of certificated and connect the DK to...
Hi everyone
Currently, I am working on a project related to the mesh network friendship feature on nrf52840. I am having the following problem: I have established a friendship...
