Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
I'm using NCS version 2.6.1 with a NRF9161DK
Recreating the issue:
Follow the instructions in the readme of the sample: Cellular: nRF Cloud multi-service
Build with...
Hi nRF experts.
We are RF module manufacturer, We are developing nRF54L15d module, When we develop production test software, we need to test power off current, Using the...
I'm trying to get a gas gauge and charger IC to work on the i2c bus. Both have different addresses. I'm able to read from the gas gauge address but not the IC. Are there specific...
Hi Nordic:
I use NRF54L15 for my product and hope to use ANT+AND BLE. Does NCS2.8 currently support it?
I couldn't find a example program for ANT+in NCS2.8. How can I...
Hello support team,
I am developing a mobile app to communicate on BLE coded phy (long range) with nrf5340DK. The nrf connect for mobile on android works fine, but not ios...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
Hello,
I am going through the intermediate DevAcademy tutorials right now because I specifically need to use the 52840 dev kit to interface with a SPI driven ili9340 device...
Hi everyone,
Edit: Consider that I'm on ncs 2.6.1
What are the current methods for provisioning an nRF9160 on the nRF Cloud? I have an ongoing project with the nRF9160...
This sample can be found under samples/nrf_compress/mcuboot_update in the nRF Connect SDK folder structure.I want to know the whole decompression process,I added a lot of...
Hi,
I am building an app that connects to the NRF52840 with BLE. The NRF board is attached to an electrocardiogram(ECG) setup, so I am interested in the app being able to...
Hello,
I am using the hci_usb sample from Zephyr and running BlueZ 5.53 on Ubuntu 20.04. I am trying to increase the ACL packet size from the default value of 27 bytes and...
Hi,
I am using SDK v2.6.1.
Is there any course available on DevAcademy for WebSockets?
For WebSocket i take reference of v2.6.1/zephyr/samples/net/sockets/websocket_client...
Hello there,
I am using nrf connect sdk using vs code.
Toolchain: v2.7.0 SDK: v2.7.0
I have custom hardware board based on nrf52811 SoC.
I have completed a firmware...
Hi
We have a project previously built on NCS v2.6.0 and now we need to migrate it to v2.8.0
I see from v2.9.0 child/parent build setup is not supported and so we are planning...
