I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
If I try to repeatedly connect and then disconnect from the LTE-M network with an nRF9160 (I'm using the Actinius Icarus v2 board), I observe that the first 30 (approx...
HI ，Nordic
Currently I am trying to get voice data via DMIC on NRF52840DK and send it out via BLE after OPUS encoding, but I am having trouble: nrfx_pdm_start keeps triggering...
When using two 52833 boards for distance measurement, when testing at 60cm, the distance value obtained sometimes wobbles between 0.6-1.2m, but sometimes stabilised around...
Hi,
I am using nrf SDK v2.3.0 with nrf Connect extension of VS Code on MacOS
The nrf Connect Extension was automatically upgraded to v2023.9.169 last week.
I noticed...
Problem Statement:
I am working on a project where I want to stream audio from a customized Android app to the nRF5340 Audio DK over Bluetooth Low Energy (BLE) . The nRF5340...
I am using ncs version 2.5.0.rc-1, I want to initialize the icm-42670 using nrf52832 zephyr ready made driver for invensense. But i continuously seeing sensor: Device not...
Hi,
We are profiling our custom battery to get the battery model. using the nRF fuel gauge connected to the nPM1300-EK board as we intend to use the nPM1300 nrf_fuel_gauge...
Hello!
We. are now developing on nrf82840 , using zephyr SDK 2.6.1 with toolchain v2.7.0
when our program runs, psa_import_key always return error code : -134
After...
ICM42670P and nrf52832 were tested in examples such as spi and spis to configure them as SPIs, but data could not be received. Can someone help me? configured with sdk 17...
I am using nrf52840 dev kit to connect to nrf connect app on my android phone. I using ble_app_uart example to fetch Mobile mac ID when event BLE_GAP_EVT_CONNECTED is triggered...
Hi
I am using the nRF5340 DK board using its P20 trying to flash an LED blink code to MDBT53-P1M (RAYTAC) I/O shield. The LED is connected to P0.31 of the I/O shield. By...
I am using Bluetooth for DFU in NCS version 2.6.1, but I encountered an issue in Device Manager that says, "There is no free slot to place the image." In the JLINK RTT, I...
Hi
I am new to the nRF52832 + nRF Connect and have recently purchased the nRF52 DK. Sorry if this is a simple question, but I want some clarification.
I have an external...
We have a custom board with an nRF5340 connected to a W5500 ethernet interface. The interrupt handler for the W5500 is never executed, despite the interrupt signal being asserted...
Hello, In the DevAcademy lessons I'm currently running blefund_less2_exer1 on the nRF52840 board. Successfully build and flashed firmware using Visual Studio Code enfironment...
