I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi,
I run a couple test with the PPK2 on our board to measure and optimize the power consumption, but I had some weird results and I'm hopping you can help me out to understand...
Hi,
I am looking at setting up some of our team with the ability to flash our custom devices that contain various chips (nrf52, nrf53, nrf91). Assuming the SEGGER software...
Hi,
I can't program nRF52840 dongle using Programmer Tool on Linux.
Dongle is visible, can be selected and memory content read without any problems but file write attempt...
Hi nordic support:
Our product used nRF52840 and nrf5_sdk_17.1.0. It's inconvenient to connect UART port when perform DTM test to testing nRF52840's RF performance. Could...
Hi there,
I hope this message finds you well!
I’ve been developing several products using Espressif’s modules that offer both Wi-Fi and BLE on a single SoC. I wanted to...
I'm developing a custom board that uses the nRF54H20.
The Getting Started guide for the nRF54H20DK explains how to use the pre-built BICR file and program it to the chip...
Hi Team, We are facing significant range issues on iPhones and other iOS devices with our hardware. We have tested these with both Custom App ( Made in House ) as well as...
Hi Nordic team,
I’m working on an nRF9151 DK with nRF Connect SDK v3.0.0. My goal is to send GNSS latitude/longitude data to a CoAP server.
The GNSS sample works fine...
Hello,
I have a series of nRF52840 devices that are already connected together in a Thread Network.
My system is composed by one client and multiple servers.
1) I'd...
Setup
Hardware: Nordic nRF7002DK as Wi-Fi STA (client) .
AP & Receiver: a Linux PC creates a Wi-Fi Hotspot/SoftAP (NetworkManager/hostapd) and simultaneously runs...
Hi,
I recently followed the instructions to install nRF Connect on Visual Studio by completing Exercise 1 of the nRF Connect SDK Fundamentals course: Exercise 1-1
I noticed...
I am trying to set CONFIG_TFM_BL2 and it seems like it cannot be set to 'y' because CONFIG_TFM_BL2_NOT_SUPPORTED is also set to 'y' in ${prj_name}/build/${prj_name}/zephyr...
I am using the nRF7002-DK to implement a BLE interface. I need to send packets > 23 bytes through a notification characteristic. I am currently using nRF Connect on an android...
Hello, I am using nrf52832 along with S132 soft device and SDK 17.1.0.
Can you please provide me the peer manager api that can list the paired/bonded devices? Also, is...
