Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi, I'm developing some products and i need my all devices to synchronize within 10ms difference, using UTC Time standard
Here is basic concept that i want to do for my...
Hi there,
We want to compare the power profile of the nRF9160 with a different device, but for this we want to ensure that both devices are transmitting at the exact same...
We're using nRF5 SDK v16.0.0, FreeRTOS, SoftDevice on nRF52832.
We plan on having two applications in flash. We want both applications to be able to access (read/write)...
Hi,
I am working on BLE 5, I have few queries related to connection parameters
1. Can you tell what is the min PDU size does nrf52805 BLE stack supports with LE secured...
I was wondering in Bluetooth mesh, which layer defines the Relay, Proxy, Friend, and the Low Power features for nodes? For example, is it done by the application, Link layer...
Hi there,
I have nrf52833dk and i have implemented the direction finding examples from nrf connect sdk. kindly guide me about antenna hardware setup that i need to do with...
Hi,
Please excuse me if I ask some stupid questions I am new to wesr and have only used git simply over the last few years. These questions stem from trying to get percepio...
Hi,
I'm designing my own algorithm for direction finding and for that i need IQ value as input. In NCS v1.6.0, in the locator exemple for aoa, the IQ value are store in...
hello,
I'm using SPI in NRF52840 with sdk16, In Nordic Dev zone forum I have read that we can configure frequency of SPIM3 up to 32 MHz but in actually as I can see there...
Hi All,
I am trying to make a project for RGB lights using nRF52-DK using NCS.
In these lines of code I am getting the following error -
'DT_N_ALIAS_rgb_pwm_P_ch0_pin...
Hi All,
wondering if anyone else has experienced this. I'm currently developing a program based off of the ble_hids example in SDK17. Currently I'm using the app_timer...
Hi All,
Setup:
SoC: nRF51822
SDK: 11.0.0
Softdevice: S130 2.0.1
I am facing occasional HardFault and It is happening randomly. I need to test device few hours...
Hi Team,
I am trying to perform firmware update of nrf52840DK using MCUBOOT bootloader over UART. I have followed the link: https://devzone.nordicsemi.com/nordic/nrf-connect...
Hello everyone,
How can I use rand() and srand() functions in NCS?
I have already #include <stdlib.h > , but I got this issue:
undefined reference to `srand'
Thanks...
