Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
In the NRF5 SDK 17.0.2 ble_nus_c.c are two calls to the evt_handler without setting event.conn_handle.
Please find attached a patch to fix this for on_hvx() and ble_nus_c_on_ble_evt...
Hi,
I'm trying to figure out what could make the current consumption difference between your blinky example with freertos and with the timer example ?
Here is my configuration...
Hello, this is my current setup: - nRF52840 acting as NUS peripheral, with properly configured coded phy (nRF SDK) - nRF5340 acting as NUS central, with properly configured...
Dear friend，
I am doing a test like this: 1. Connect the Bluetooth device with the nrf conncet app of the Android phone. 2. The notify (CCCD) is enabled. 3. Click "disconnect...
Hi,
we are using D- and D+ in our nRf52833 board, I want to use the CDC ACM USB class as Virtual COM port.
I found that there has a demo example in the \examples\peripheral...
Hi,
We have a problem that occurs when
1) the GPS is at bootup of nrf91: indoor when we start the GPS search, and it doesn't find anything or maybe just 1 satellite...
Hi,
Looked through PS v1.3 didn't see any reference, so probably the answer to my question is no.
But can you please confirm that for me - does nRF52833 support boundary...
Hello,
I am doing tests on nRF9160 DK and I observe that if I send more than 1024 bytes on a TCP or UDP socket, the bandwidth drops.
Here are some numbers :
for...
Hi there
I mount the 19pin connector on nrf5340dk board and connect to segger j-trace pro . The debugger function work well.
Later i modify the nrf9160 etm trace project...
Has anyone had success getting triggers on motion to work with the LIS2DH? I only have INT1 wired so I modified the drivers to work on INT1 as the spec document says it should...
I'm writing software for nRF52832 using nRF5 SDK v17.0.2
I'm using a timer to create a buzz/tone using timer 3. This works as expected.
I'm also using the SAADC to measure...
I'm learning how to use OTA DFU (via BLE) now. I have Python 2 and 3, pip installed in my Win10 laptop. When I install the nrfutil with PowerShell, I had some errors (see...
I've been using the nrf connect toolchain for a bit, and after some initial trouble it was working ok, but now its randomly giving this error whenever I try to build anything...
Hi,
I am trying to convert a number from little endian to big endian. There is a built in function "NTON" that I can use instead of writing my own code, but I can not find...
