Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Because I need to receive the serial interface in the event handler of the serial data communication protocol (custom) send out via bluetooth, a set of protocols to 25 bytes...
hi:
the nrfutil link: github.com/.../mesh_dfu
I've been having a little bit of an issue running the command "python setup.py py2exe" in cmd.exe
the error as follow:...
I'm using the nRF52 + SDK11.0.0 + s132. I have a single physical button on my hardware that can be used to toggle power to the system (though a PMIC). This same button routes...
Hello Nordic!
This question is a follow-up on this topic , where it is suggested to keep track of BLE_GAP_EVT_CONNECTED and BLE_GAP_EVT_TIMEOUT events in order to know...
Hi, Nordic Forum!
I'm developing a product that relies heavily on the TWI in master mode. I was using SDK 11.0 and everything was working well.
I decided to port to...
I want to use another MCU(MT7688 run OpenWRT) as a upper monitor to DFU the nrf52832,But you know,the way of serial download for nrf52832 is use nrfutil with command that...
Hi There,
We are having an issue reading data from the ble_gatts_evt_rw_authorize_request_t.request.write.data buffer. We are writing the data to the characteristic using...
I need to receive both UART Service data and HRS service data on the app.
Currently I have seen on Nordik Connect app , both the services can be found and can connect and...
So we have the Arduino 101 board talking to a heart rate sensor MAX30100. When we run the nrf connect app on android it is able to connect to the sensor with no issues. When...
Sporadic program restart from main.
I suppose, it is hardfault exception. How can I catch it?
Check pls my memory settings.
ROM: start- 0x1c000 size 0x23000
RAM: start...
Im implementing an application which uses the s132 SD for BLE communication and the mesh implementation described at nRF51-ble-bcast-mesh. I need to have encrypted and authenticated...
Hi Forum,
I'm using SDK12 without ble. (peripherals/uart)
so, I can't pstorage or fstorage.
I want to write 4 bytes without erasing a page. And I want to update a value...
Hi. I'm using nRF52832, SDK13.0.0, S132.
When I make bootloader, I should make *.setting file for application.
Do i need *.setting file when I update just application...
Hi,
this is not a question about the nRF but about Android programming. Hope some of you can help me anyways. I modified the android part of the nRF Blinky example github...
Hi Nordic Team,
I saw some issue with Nrf connect on IOS.
First the App crash when i open it.
Second with IOS i can see some issue with pairing and bonding...
