I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm developing a project, where I use nRF9151 as a GPS sensor, and nRF52833 as a BLE gateway. I want to send data from 9151 to 52833 over one of UARTs. The problems I'm facing...
Hello,
I’m currently working on a hardware design using the following components:
nRF54L10 SoC
nRF21540 Front-End Module (FEM)
2450AT18B0100001E chip antenna...
I'm developing a project for nRF54 using NCS. I have a question regarding the placement of the BLE protocol stack. In the previous nRF5 SDK, the protocol stack was usually...
I have downloaded the nrf connect software and downloaded the segger drivers. I cant see the drivers in mi windows drivers administrator. The evk is powered by the usb because...
Hardware env: New designed board with NRF52840 + NRF9151, which 52840 connect 9151 via uart
Software env : NCS version: v3.1.0 (new installed) Nrfutil version: 8.1.0 (34e21a1...
Hey, since iOS version 18.6.2 the BLE connect to our BLE peripherial with nrf52840 getting disconnect events. Also the range between them is very bad. The connection parameter...
I'm currently working on some projects for the nRF54 platform using NCS and VS Code. I want to delete the unused files in my project because the codebase has become too large...
In the nRF52840 Product Specification PDF v1.11, on page 323, the third paragraph down states:
1. "If the CPU performs a clear operation on a bit in the LATCH register...
Hi Team,
below mention errors I am getting west build process.
* Executing task: nRF Connect: Generate config HVPP_BLE_Board_Files/nrf54l15/cpuapp for c:\Haritha\Github...
hi support team，
customer told me 54L15dk debug out is not able to program another 54L15 chip.
so i tried,
1. A-54L15dk debug out program B-54L15dk debug in, failed...
I'm trying to leverage the asset tracker project form nordic 9160dk to actinius icarus 9160 board, i use tagconnect 2030 to connect P19 of dk and icaurs, but the jlink cannot...
When I try to add OTA image compression for MCUboot, the RAM utilization skyrocks and is not compatible with the nrf52833. Is there any way to cut out any and all excessive...
Hi, I'm working on a product that uses nRF52840 (The custom board actually has the Ebyte module E73-2G4M08S1C). nRF5 SDK 17.1.0. The firmware consists of: 1. Bootloader -...
