I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi, I'm developing some products and i need my all devices to synchronize within 10ms difference, using UTC Time standard
Here is basic concept that i want to do for my...
Hi there,
We want to compare the power profile of the nRF9160 with a different device, but for this we want to ensure that both devices are transmitting at the exact same...
We're using nRF5 SDK v16.0.0, FreeRTOS, SoftDevice on nRF52832.
We plan on having two applications in flash. We want both applications to be able to access (read/write)...
Hi,
I am working on BLE 5, I have few queries related to connection parameters
1. Can you tell what is the min PDU size does nrf52805 BLE stack supports with LE secured...
I was wondering in Bluetooth mesh, which layer defines the Relay, Proxy, Friend, and the Low Power features for nodes? For example, is it done by the application, Link layer...
Hi there,
I have nrf52833dk and i have implemented the direction finding examples from nrf connect sdk. kindly guide me about antenna hardware setup that i need to do with...
Hi,
Please excuse me if I ask some stupid questions I am new to wesr and have only used git simply over the last few years. These questions stem from trying to get percepio...
Hi,
I'm designing my own algorithm for direction finding and for that i need IQ value as input. In NCS v1.6.0, in the locator exemple for aoa, the IQ value are store in...
hello,
I'm using SPI in NRF52840 with sdk16, In Nordic Dev zone forum I have read that we can configure frequency of SPIM3 up to 32 MHz but in actually as I can see there...
Hi All,
I am trying to make a project for RGB lights using nRF52-DK using NCS.
In these lines of code I am getting the following error -
'DT_N_ALIAS_rgb_pwm_P_ch0_pin...
Hi All,
wondering if anyone else has experienced this. I'm currently developing a program based off of the ble_hids example in SDK17. Currently I'm using the app_timer...
Hi All,
Setup:
SoC: nRF51822
SDK: 11.0.0
Softdevice: S130 2.0.1
I am facing occasional HardFault and It is happening randomly. I need to test device few hours...
Hi Team,
I am trying to perform firmware update of nrf52840DK using MCUBOOT bootloader over UART. I have followed the link: https://devzone.nordicsemi.com/nordic/nrf-connect...
Hello everyone,
How can I use rand() and srand() functions in NCS?
I have already #include <stdlib.h > , but I got this issue:
undefined reference to `srand'
Thanks...
