My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hello,
We are in pre-production and we need to make 1000 prototypes.
Here is the filter we planned to use : https://www.johansontechnology.com/datasheets/2450FM07A0029...
Hi support team,
Customer needs them for BLE certification though I think those in nRF52840 report are same.
BTW, may I pre-fetch nRF5340's for any future request? ...
Hello,
Have any developers here on the forum had luck with getting the nRF9160 DK working in India?
Our India dev team has looked extensively and has not yet been able...
Hi, dear Nordic.
I tried to build secure_bootloader_ble_S132_pca10040 project in Segger. And it gives me this error message:
cannot find ../../../../../external/micro...
Hi,
I am trying to get my nrf24L01+ to communicate with nrf5340 using the enhanced shock burst sample code. In the sample code there are LOG_INF, LOG_ERR, LOG_DBG commands...
Hello Nordic Team,
We are in production phase, and flashing our modems one by one does not work well. It is too slow process, so we are looking for a solution that can offer...
Hi,
I'm trying to develop a Bluetooth Mesh Network using 3 Thingy52s and one Thingy91 that acts as a gateway to Azure IoT Hub. I saw the sample code LTE BLE Gateway for...
Hi,
I am trying to get the Atmel WINC1500 module to work with the nRF9160DK.
I have read a similar post,
https://devzone.nordicsemi.com/f/nordic-q-a/76640/spi-issue...
Hej!
I am trying to make a circuit / configure my SW for using the nRF5208 to have a small power consumption when not trainsceiving . Basically, I need my setup to have...
Hi! The nPM1100 is advertised specifically as a complementary product to the nRF52 and nRF53 product line. Seeing how the nRF9160 can also operate at 3V, I was wondering why...
Hello, I am working with an nRF52811 and I am trying to get it to send data via UART with a USB connection. I tried using the USB CDC ACM module, but it appears to only work...
Hello,
my application requires a reliable break detection (The serial data input is '0' for longer than the length of a data frame) sent from a peer device on the UART RxD...
I am working on reading and writing data to an external QSPI flash (MX35LF4GE4AD) that has an internal cache mechanism. I have been able to read/write to the flash using standard...
I am currently working on a project developing a USB HID product based on the nRF52840. I have run into an issue regarding USB communication reliability and am seeking the...
