I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi,
I want to merge provisioner and client to provision, configure and control multiple servers from the provisioner+client module.
SDK = nRF MESH SDK v4.2.0
Example...
Hey guys,
All of a sudden, I'm not able to flash my nRF board anymore. I get the following message when I try to connect to the board using segger IDE.
And when I try...
Hello,
I had purchased 6 nRF52840 Preview Development Kit boards in 2017 for study and development.
This year, I want to re-use the PDKs for a new BLE-THREAD related PoC...
Hi, i'm trying to load the aws_iot sample and I'm running into mqtt_connect, error: -95. Based on other posts, it seems my certificates might not be properly loaded. As far...
I am building on a BLE DFU project which already has a NRF_FSTORAGE_DEF for allocation of non-volatile data used by DFU. I want to add another instance of NRF_FSTORAGE_DEF...
Hello,
I am using the modem callback:
To check if the modem is connected using the following code:
However, as far as I understood this only indicates that the modem...
Respected Sir, Mam
I am Noel Joe Riju Antony a student of Amity University, Noida, India pursuing a B.Tech in Aerospace engineering. I am currently working on a CW radar...
Hi,
I've got a Thingy:91, which I've spent a lot of hours in understanding the different samples. I want to be able to send GPS information to my Azure IoT hub device...
Utilizing SDK 15.2 and Softdevice S132, when debugging with Segger Ozone and starting from main or after triggering a reset to restart at main an ERROR 8 [NRF_ERROR_INVALID_STATE...
Tried running android app in debug mode, but I could not see any data on the crash.
tried resetting the board a few time and re commissioning.
followed the guide to set...
I found a lot of posts with this warning/error, but I could not find a fitting solution among them.
in my case, I copied the `peripheral_lbs` project to another folder,...
Hello
I have a few questions regarding the "ble_thread_dyn_mtd_coap_cli" example:
In the "main.c" file, I notice that you have created timers to call "sd_ble_gap_conn_param_update...
Hello.
I have a custom board with a uBlox BMD300 on it. The BMD300 is based on the nRF52382. The BMD300 had a pre package firmware in it that acted as a BLE UART bridge...
