Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
When I start the TX sweep test with all 80 channels I get only 10 channels used by the RF.
Also power strength of the channels is modulated.
cf. attached frequency...
Hi
I am developing an iOS app that needs to communicate to an nrf51822(working in ble peripheral mode). The peripheral to which the app connect is selected using mac address...
hi nordic team：
I was wondering if the main program is too complex, and do not use the scheduler, and the connection parameter settings are correct. Whether because the...
Hello,
I have tested the DFU and everything works fine. Normaly the device enters into DFU mode with a pressed button 7, meaning the level on I/O 7 is LOW.
But in my...
Hi,
I've an HardFault, the program crash to the HardFault service routine at this row of the twi_hw_master.c:
--> NRF_PPI->CH[0].EEP = (uint32_t)&NRF_TWI1->EVENTS_BB;...
Hello, I am doing some dev on the NRF51822 with a Cortex MO manager. I have trouble on the MISO pin, and I am wondering if I have to drive this MISO pin by any kind of pull...
I've read in several other posts that it's possible to send up to 20 bytes per notification packet using sd_ble_gatts_hvx(). I've also read that we should not edit the file...
Hi,
In the step 3 of the "nRF51822_Development_Kit_User_Guide_v1.4" (page 11) :
Select nRF51822 from the Select Target list and click Build or press F7 to compile the...
Hello
I'm developing software for beacon-type device based on NRF51822. It has no buttons or other user inputs. Our use case:
User buy beacon-device. First phone which...
I've been working with SDK 7.0.1 and it seems there are some issues with device_manager_peripheral.c.
First off it doesn't compile out of the box, the debug code is turned...
In the document nRF51822-PAN v2.4.pdf, PAN #9 says that OUTINIT doesn't work,
"Initial value for GPIOTE output after configuration is undefined"
and example workaround...
SDK 7.0.1 is intended for version 2 (G0) chips, and the future. So it can't be used with earlier versions of the chips (like C0). So it shouldn't have workarounds for C0 chips...
I have recently begun running into issues related to the SPIS module on my nRF51822 S100 v7.1. Fairly often, between 10 and 20% of the time, the interrupt does not fire when...
Hi,
I am using TIMER2, GPIOTE and PPI to implement a 6250Hz square wave at a GPIO pin. I can successfully create the square wave on the GPIO pin. However, I would like...
