Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello. I'm trying to do spi communication on a custom board with nrf5340 used. I'm using three threads, I build it, but if I put it on the board, the board will have a problem...
Hello I’m using the NINA-B306-00B BLE module which uses the nRF52840 MCU for a custom board application. The BLE module interacts with two sensors, an accelerometer via SPI...
Hello, I get a compiler warning when I try to log a float value using the LOG_INF macro in my project. The code I'm using is from the cell-fund course: lesson 6, ex. 1. Toolchain...
HI,
I have a function testfun from a customer-provided .a library, and I hope to run this testfun function in RAM. I am currently using NCS 2.8 based on the nRF52840. I...
Hi, I read others cases obout the problem to send more than 20 bytes trhough BLE and add on my prj.conf the next three lines:
This is the entire prj.conf:
Butr when...
NCS 2.7.0
NRF52840 DK
I am trying to trigger an advertising sent callback to indicate advertising timeout or a maximum number of events. I have tried increasing the workqueue...
Im using nrf5340 with nrf connect SDK 2.6.
Im trying to follow this post to evaluate hardware timer for reading saadc
But I constantly am getting
CONFIG_NRFX_TIMER1...
Hi,
I have successfully built and ran the MQTT sample ( /opt/nordic/ncs/v2.7.0/nrf/samples/net/mqtt) on the nRF9160-DK. I did have a few problems with SIM coverage and firmware...
Hi,
running the latest nrfconnect vscode extension (v2024.9.31) the "Add configuration wizard" comes up and stay blank. Additionally, the Actions view is also empty, while...
Hello
I am trying to initialize qspi in a ".cpp" file and methods like
PINCTRL_DT_DEFINE ( QSPI_NODE ); are giving me "out-of-order initializers are nonstandard in C...
Hello,
Currently, I am working on the nRF 52840 DK and the UART port named uart0 is connected to the on board debugger, Where do i find the pins for the UART1 ? I could...
Hi,
I was at the stage to do current measurment on my nrf52DK for my application, but once I cutted SB9 and powered it back by USB, the 4 leds on the board lighted up...
We are planning to base a GATT and LE Audio design off of the latest nRF Connect SDK v2.6.1 and looking into Bluetooth certification. I have found the QDIDs for the Host and...
Hello,
I am trying to use SPI driver to read BMI270 IMU data on my nRF52840dk. I stucked at verifying the sensor ID step. According to the datasheet, sensor ID is stored...
Hello,
I tried to read and write the OTP region in UICR of nRF5340 with nrfutil, but got the following output:
Any Ideas, what could be the issue here? Does nrfutil...
