I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Dear DevZone,
I believe I am quite familiar to this forum due to my ongoing Wi-Fi issues with SDK 2.6.1 To determine if a newer SDK version will resolve these problems,...
Hi,
I still try to configure Nordic-Zepyr build for a nrf5340, with a BLE stack and MCUBoot as the bootloader. The application will receive image updates over MQTT and store...
Hello everyone,
I'm having an issue with my nRF52840 Dongle. I can detect the device with nrfutil device list command, which shows:
> nrfutil device list DC1D9FD62EC5...
Hello Team,
I am trying to change the Lesson 9 Exercise 5 nrf5340_both_sol sample to use internal flash for FOTA. The code builds successfully. I have changed the pm_static...
Hi ,
I would like to use an external GPS active antenna on the nRF9151 EVB for testing (J2), does it disconnect the on board antenna GPS ? should I connect/disconnect any...
Trying to install NRF Command Line Tools. Platform is Linux 64bit x86 (distribution Ubuntu 22). I already have installed utilities by Segger, which may be the reason why NRF...
Question 1: I am using GPIO external interrupt. Does this interrupt belong to GPIOTE PORT EVENT by default? Question 2: How to configure low precision GPIOTE? Question 3:...
I use NCS2.5.0,and I noticed that there are two files(bluetooth.h and scan.h) can help to set scan parameters.Is there any difference betwen these two files?Can I call the...
Suddenly DFU OTA fails most of the time while trying to update units with code & "not secure" bootloader that has been working for years. The FW upload stops at 2% to 8% but...
Hi,
This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
Hi,
I am trying to optimize my nrf52840 application for power consumption. If I run simple loop using nrf5 SDK i get ~1.2mA. However with similiar code on Zephyr: I get...
Hi,
I am developing a small beacon application using the nRF 52805 device, and the intent is that it will send advertising packets at a slow rate, to indicate to a partner...
I'm working on implementing arithmetic operations using the PKA engine on the nrf52840 in Rust, following the CRYPTOCELL — Arm TrustZone CryptoCell 310 datasheet. While I...
Hello all,
I have been working on the implementation of the PKA engine on CC310, and have been encountering some unexpected behaviours when using the modular multiplication...