I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
The value of
ACCESS_SUBSCRIPTION_LIST_COUNT is 7,
but when I add more than 3 group in subscription of a node, its shows insufficient resources error.
What is maximum...
Current situation:
I am using uarte to communicate over UART, at Individual level this works. I have serial mesh DFU implemented in my application and at individual level...
I have been able to recieve data from individual Thingy52 modules on RPi 4 in Python.
How can I setup my RPi to communicate with multiple modules?
A straightforward approach...
Hi Everyone,
I am using nRF52832 with SDK v14.2 and SD v5.0.0 for our product development on a custom chip.
While pairing for the very first time with the smartphone,...
Hello,
I am using nrf52832 board, having SDK 15.3.0 in Segger studio IDE, using window10.
I am trying to read from ADS1232 IC,
Connection:
DOUT - P0.11
SCLK - P0...
Hello,
In ble_advdata_short_name_find,
&& (parsed_name_len < strlen(p_target_name))
should be
&& (parsed_name_len <= strlen(p_target_name))
Right now, if the short...
Hello,
I am looking at the nRF51822 and was wondering if I have the input buffer disconnected, is there a difference in current consumption for that pin if it is not connected...
Just saw the announcement of the Arduino nano 33, based on the nRF52840 and mbed RTOS. Presume it'll take a while for all of this to come together, both HW availability and...
How to set the tick of RTC to, for example, one second. And then calculate the current time base on the RTC counter.?
i need to calculate time from the RTC so that i can...
Hi all,
During development I've run into issues setting up a functioning characteristic notification for IOS or Android. The notification works fine using the NRF Connect...
This is the ticket:
https://devzone.nordicsemi.com/f/nordic-q-a/52310/how-to-switch-a-node-into-provisioning-configuration-mode-to-configure-with-nrfmesh-app-and-then-into...
Hello, we seem to be having an issue with LE privacy. We want to always use a random address when advertising, here is what I am seeing.
- SDK 15.3, Nrf52840.
If I disable...
Hi,
I'm working on enabling APP Protection while successfully executing below code:
if (!nrf_sdh_is_enabled()) { if (VERSION_BUILD <= MAX_RELEASE_BUILD) { NRF_UICR-...
Dear all,
I'm using and nRF51822 chip for implementing a wireless HID device with dongle.
The device has an RGB LED, and indication scenarios for different modes are played...
I'm using SDK 15.3.0 example twi_scanner with Segger Embedded Studio. I do a search entire solution for TWI_SCL_M and the only location it shows up is in main under the twi_master_init...
